Land Rover Parts

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Rear Toe Link is a rear suspension control link that sets and maintains rear wheel toe alignment. It connects the rear cross member to the wheel c...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Vacuum Hose for the brake servo (booster) vacuum supply circuit, connecting the engine vacuum pump to the servo inlet. On diesel applications the ...

Blade Assembly - Wiper

Rear Anti-Roll Bar Bush for the rear stabiliser (anti-roll) bar. The bush locates the anti-roll bar to its mounting bracket, permitting controlled...

Spacer (Pair)

Suspension Arm Bush for the front upper suspension arm, moulded in polyurethane rather than bonded rubber. The shouldered bush locates in the inbo...

Suspension Arm Bush for the front upper suspension arm, part of the front suspension arm and anti-roll bar assembly. The shouldered bush is presse...

Door Handle Cap for the exterior door handle assembly, fitting at the outer end of the handle in the position the lock barrel would otherwise occup...

Brake Disc - Solid - Rear is a solid (non-vented) disc forming the friction surface of the rear disc brake assembly. The disc mounts to the rear h...

Front Door Weatherstrip is the primary seal at the front door opening, closing the gap between the door and the body aperture. It limits water and...

Exhaust Manifold Nut is a hexagon nut used on the exhaust manifold fixings of the 2.2L 16V common-rail diesel engine (DW12). Manifold fasteners ru...

Brake Servo Vacuum Hose connecting the engine vacuum pump to the brake servo, within the master cylinder and servo assembly. It carries the vacuum ...

Front Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...

Rear timing belt kit - fuel injection pump drive for the 3.0L V6 turbo diesel engine. The rear belt drives the high-pressure fuel injection pump a...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Rear Door Wiring Harness - the door-side section of the body electrical system, passing through the door pillar grommet into the rear side door. T...

Rear Step Assembly - the production-fit folding step mounted at the rear of the vehicle, below the rear door. The step provides footing for access...

Damper Assembly

Absorber Shock Assembly

Damper Seal Kit - service kit for renewing the seals within the air spring assembly, covering both the front suspension struts and the rear shock a...

Rear Air Spring - the air bag element of the rear air suspension, used on both four-corner air suspension and front-coil/rear-air self-levelling sy...

Jumper Wire Assembly - rear bumper wiring link in the body electrical system, for vehicles equipped with the rear parking aid. It bridges the rear...

Brake Disc - front axle, internally vented. The disc provides the friction surface that the front brake pads clamp against, converting the vehicle...

Rear Bumper Cover - the upper tread panel section of the rear bumper assembly, finished in Brunel Metallic. It fits to the top face of the rear bu...

Exhaust Gas Temperature Sensor operates within the exhaust after-treatment system on diesel engines equipped with a Diesel Particulate Filter. Ins...

Engine Mounting Bracket for the 3.0L V6 turbo diesel engine, part of the engine mounting and support assembly. The bracket bolts to the engine and...

Starter Motor for the 2.2L Td4 diesel engine (DW12), part of the engine starting system. It cranks the engine through a pinion that engages the ri...

Trim Clip, male half, used in the facia and dash trim assembly. The clip is the male part of a two-piece push-fit fastener. It locates in the trim...

Idler Pulley for the front auxiliary drive belt on the 2.7 and 3.0 V6 diesel engines, part of the pulleys and drive belts assembly at the front of ...

Bumper Moulding - Front is the moulded end cap that closes off the outer end of the front bumper, forming the finished corner profile and taking th...

Bumper Moulding - Rear is the moulded end cap that closes off the outer end of the rear bumper, forming the finished corner profile and taking the ...

Head Gasket - 3.0 TDV6 - Grade 3

Brake master cylinder for vehicles fitted with the four-wheel anti-lock braking system. It sits in the brake hydraulic circuit between the brake se...

Parcel Shelf Catch Clip is the retaining catch for the load compartment cover (parcel shelf), part of the loadspace trim assembly. Supplied in an e...

Accessory Drive Belt - ribbed serpentine belt for the front-end accessory drive of the 5.0L naturally aspirated V8 petrol engine. Driven from the ...

Oil Level Sensor - electronic engine oil level sensor mounted in the wall of the sump, forming part of the engine lubrication monitoring circuit. ...

Engine Cover - 2.4 Diesel

Jack Handle supplied in the vehicle tool roll. It operates the standard-equipment vehicle jack, providing the leverage needed to raise and lower th...

Bracket - Front Fender - LH is a front-end body panel mounting bracket for the left-hand side. It locates and supports the front fender where it m...

Bracket - Front Bumper Upper is the upper mounting bracket for the front bumper assembly. It supports the upper edge of the front bumper cover aga...

Front Fender Bracket - RH is a front-end body panel mounting bracket for the right-hand side. It locates and supports the front fender where it me...

Crankshaft Front Oil Seal seals the front of the crankshaft where it passes through the timing cover, behind the crankshaft pulley. It retains eng...

Outer track rod end - M12 thread, steering gear and track rod linkage. The track rod end threads onto the tie rod and its ball joint connects the ...

Rear moulding cap - exterior body trim. The cap closes off the moulding at the junction between the rear bumper and the rear wheelarch moulding, c...

Exhaust Stud - M10 stud used at the exhaust system flange joints, with threaded sections of 14 mm and 26 mm. The stud is retained in the exhaust f...