Land Rover Parts

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Rear door seal RH 110

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Depression control valve assembly TD5 and 2L Freelander

Brake Hose – 1-Ton is the front flexible hose in the front brake hydraulic circuit. It carries fluid from the rigid brake pipe on the chassis to th...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Transmission metal sump kit for the ZF 6HP26 six-speed automatic transmission within the Transmission External Components system group. The kit r...

Driver's door lock actuator and switch CDL

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Specifically designed for Series vehicles equipped with the Weber 34 ICH 2.25 carburettor, this kit includes all the essential components needed to...

Shim .003" for swivel pins

Centre Exhaust Box (centre silencer), part of the exhaust system. Mounted in the centre section of the exhaust line between the front pipe and the...

Mud Shield for the left-hand inner wing, left-hand drive configuration. This panel fits beneath the wing to shield the components behind it from mu...

Decoke Head Gasket Set for the 2.25L 4-cylinder diesel engine - the top-end gasket set used for a full decarbonising (decoke) job or when removing ...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Engine Bottom-End Gasket Set for the 2.25L 4-cylinder petrol engine, supplying the lower-engine gaskets and seals used during a bottom-end overhaul...

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Wheel Cylinder - LH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the left-...

Rear Exhaust Silencer from the rear section of the exhaust system, incorporating the tailpipe. Positioned at the end of the exhaust run, it provid...

Brake Caliper Carrier Bolt secures the brake caliper carrier (mounting bracket) to the axle, providing the clamping force that holds the caliper as...

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Fuel Pump is the in-tank high-pressure pump in the fuel delivery system, mounted inside a metal fuel tank. It draws petrol from the tank and deliv...

Brake Master Cylinder - Dual-Line is the hydraulic master cylinder of the dual-line servo braking system, converting brake-pedal force into hydraul...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the fuel connector block to the engine within the fuel pres...

Brake Master Cylinder for the braking hydraulic system, converting brake pedal force into hydraulic pressure to actuate the brakes. Mounted to the...

Water Pump Gasket for the engine cooling system, sealing the water pump mounting face against the engine block. Fitted to the 11L engine block ver...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Seat Box Corner Protector - Pair - Black Steel

Air filter element Puma TD4 Def.

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

Head Gasket Set - 2.25 Petrol - Composite is a top-end (de-coke) gasket set for resealing the cylinder head assembly of the 2.25-litre petrol engin...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Wiper Arm The arm assembly within the front windscreen wiper mechanism, for left-hand drive configuration. It mounts onto the wiper motor spindle ...

Air flow meter TD5 OEM VDO /Delphi

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Maintain the timing precision and reliability of your Land Rover Defender 200TDI with this OEM timing belt kit, designed to meet original factory s...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Coolant Hose - the top radiator hose in the Td5 2.5L 5-cylinder turbo diesel engine cooling system. This hose forms part of the upper coolant circ...

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Brake Master Cylinder within the Master Cylinder & Servo assembly, fitted to non-ABS braking configurations. This hydraulic component converts...