Land Rover Parts

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Clip

Wiper Blade A front windscreen wiper blade within the wiper assembly. It attaches to the wiper arm and clears the windscreen as the arm sweeps acro...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Caged Nut securing the front door hinge to the body pillar. The nut is held in a floating sheet-metal cage that retains it against the panel and l...

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Transfer Lever Knob in yellow, for the four-wheel-drive engagement lever on the transfer gearbox. It threads onto the top of the selector lever an...

Glass Fuse rated at 10A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...

Electronic Distributor - complete distributor assembly for the 4-cylinder petrol engine, supplied with the electronic ignition conversion already f...

Swivel Pin Housing Shim - 0.25mm (0.010") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Swivel Pin Housing Shim - 0.075mm (0.003") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin ho...

Breather O-Ring for the 2.5L diesel engine (NA Diesel, 200 TDi and 300 TDi), used in the crankcase ventilation system. It seals the cyclone breath...

Oil Filter (Large) for the engine lubrication system, the large-canister filter fitted to the 4-cylinder petrol and diesel engines. The filter rem...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Panhard Rod Bushes are the mounting bushes at the ends of the front panhard rod in the coil-sprung front suspension. The panhard rod locates the fr...

Joint Washer for the transfer gearbox top cover. This gasket seals the joint between the top cover and the transfer box housing, preventing oil le...

Swivel Pin Kit for the upper front axle swivel assembly, ABS applications. The kit serves the top swivel pin - the pivot interface between the swiv...

Rear Shock Absorber - rear suspension damper for the long-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls sp...

Flasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Wheel Bearing Kit for overhauling one wheel hub to imperial specification, front or rear. The hub runs on an inner and an outer bearing, which car...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Cylinder Head Gasket - non-adhesive type, for the 2.25-litre petrol engine. Seals the joint between the cylinder head and the cylinder block, cont...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Rear Shock Absorber, standard-travel, for the rear axle suspension. The damper controls vertical movement of the rear axle and damps spring oscill...

Exhaust Downpipe Assembly from the front section of the exhaust system, for the Td5 2.5L 5-cylinder turbo diesel. Installed directly downstream of...

Drive Belt is the auxiliary drive belt for the 3.5L V8 petrol engine. Running from the crankshaft pulley, it drives the alternator and, where fitt...

Selector Rod Rubber Grommet Washer is the rubber sealing element fitted around the reverse gear selector shaft at its exit point through the Series...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Brake Pad Fitting Kit - Solid Disc - Front

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Bottom radiator hose SII(A) 2.25

Wiper Blade for the windscreen wash/wipe system, 25 cm in length, of flat-blade construction. The blade attaches to the wiper arm and carries the ...

Service Sticker - a self-cling window sticker for recording engine oil service intervals. The sticker carries the Castrol logo on one face; the re...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Differential pinion oil seal rear Salisbury axle from VIN XA159807

Starter Motor Repair Kit for the solenoid on the Td5 starter motor (NAD101240). The kit renews the solenoid's copper contacts and plunger - the pa...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...