Land Rover Parts

Sump Gasket sealing the oil pan (sump) to the cylinder block. Forms the oil-tight joint between the sump and the engine block, retaining engine oi...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Front Brake Pad Wear Sensor, part of the front brake pad and caliper assembly. The sensor is a sacrificial wire loop held in a moulded carrier tha...

Window Regulator and Motor - rear door window lift mechanism, supplied complete with its electric drive motor. The regulator sits within the rear ...

Rear suspension toe link, left-hand side, from the multi-link rear suspension assembly. The toe link runs transversely between the rear subframe a...

Front Suspension Arm Bush - the rubber-bonded pivot bush that mounts the front suspension arm to the subframe, within the front suspension arm asse...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Door Latch for the left-hand front door. The latch secures the door to the body striker and integrates the central-locking and dead-lock mec...

Throttle Body and Motor - electronically actuated throttle valve assembly in the engine air intake system, mounted at the intake manifold inlet. T...

Radius Arm and Left - Front - RH

Front Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...

Suspension Arm - front lower arm, rear position, right-hand side. Part of the Front Suspension Lower Control Arm assembly. The arm locates the low...

Suspension Arm - upper front control arm for the right-hand side, 247 mm between pivot centres. The arm ties the top of the front wheel knuckle to ...

Timing Cover Oil Seal is the front crankshaft oil seal, located in the timing gear cover. It seals around the crankshaft where it passes through t...

Wheelarch Eyebrow, front, left hand, part of the front wing and wheelarch assembly. The eyebrow fits over the top edge of the front wheelarch aper...

Camshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...

Drive Belt Tensioner

Suspension Arm - the rear lower control arm on the right-hand side of the independent rear suspension assembly. It links the rear subframe to the ...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Front Brake Disc - vented cast iron disc for the 18-inch front brake package. Mounts to the front hub behind the road wheel and provides the frict...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Suspension Arm is the front upper suspension arm (wishbone), left-hand side, within the front suspension assembly. It locates the upper section of...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Front Brake Hose - the flexible section of the front brake circuit, running between the rigid brake pipe on the body and the front brake caliper. U...

Brake Vacuum Pump, the auxiliary vacuum source for the brake servo on petrol engines. Petrol engines - particularly direct-injection and superchar...

Brake Pad Wear Sensor monitors rear brake pad wear, fitted to the rear brake pads within the rear disc and caliper assembly. As the friction mater...

Front Wheel Arch Moulding for the right-hand side, part of the exterior body cladding assembly. The moulding follows the flange of the front wing ...

Air Mass Meter (mass air flow sensor) for the M62 B44 4.4L V8 petrol engine, mounted in the air cleaner outlet of the intake air system. The senso...

Oil Filter Gasket from the oil cooler and filter housing assembly of the 4.4L DOHC DITC V8 diesel. The gasket seals the oil filter housing against...

Heater Manifold - the rigid coolant tube running from the engine block to the heater inlet hose on the 3.0L DOHC GDI supercharged V6 petrol engine,...

Shock Absorber Bracket in the rear suspension. It locates and secures the rear shock absorber, providing the mounting point that ties the damper t...

Front Brake Pad Wear Sensor for the front axle brake assembly, forming part of the brake pad wear warning circuit. The sensor is a wire loop carri...

Front Brake Disc - a vented front-axle brake rotor forming part of the front disc-brake assembly. The disc is bolted to and rotates with the front...

Rear Wiper Blade forms part of the rear window wiper system, clearing rain and debris from the rear window glass as it is swept across by the wiper...

Heated exhaust gas oxygen (HEGO) sensor, rear (post-catalyst) position, for the 4.4L V8 petrol engine (M62 B44). The sensor sits in the exhaust do...

Cabin Pollen Filter, 272x195x43mm - the filter element in the HVAC intake housing, installed upstream of the blower motor and evaporator. All air ...

Top Radiator Hose from the engine cooling circuit, connecting the radiator to the engine on the upper leg of the circuit. It is a moulded hose, sh...

Exhaust Gas Pressure Sensor for the diesel exhaust aftertreatment system. The sensor is connected by take-off pipes to the exhaust upstream and do...

Front Lower Suspension Arm is the left-hand lower control arm (wishbone) of the front suspension. It locates the front wheel hub carrier to the su...

Cylinder Head Gasket for the 4.4L V8 petrol M62 engine, sealing the joint between the cylinder head and the engine block across cylinders 5 to 8. ...

Anti-Roll Bar Link connects the rear anti-roll bar to the suspension within the rear suspension assembly. It transfers load between the stabiliser...