Land Rover Parts

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Upper Turret Mounting Bracket, galvanised, forming part of the front coil spring and damper turret mounting on the chassis. The bracket provides t...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Oil Cooler Pipe - the pipe carrying engine oil from the engine to the oil cooler within the lubrication cooling circuit of the 2.5L 4-cylinder TDi ...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single unit. The assembly mo...

Con Rod Bearing Set for the 2.25L four-cylinder petrol engine. The set provides the big-end shell bearings that carry the connecting rods on the c...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Flasher Relay controls the direction indicator and hazard warning lamp circuit, switching the lamps on and off at the regulated flash rate. It plu...

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Front Door Hinge - Lower, Right-Hand - lower hinge for the right-hand front door, mounted between the door and the body A-pillar. It forms the low...

Steering Damper - Girling

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Door Card Fixing Kit for the interior door trim assembly of the Defender, in black. This kit provides the black-coloured rivets and fasteners requ...

Window Channel - Front Door

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Fusebox Housing Bolt is the threaded fastener that secures the fusebox housing within the dashboard. It retains the fuse box mounting in the parce...

Wiper Delay Relay for the front windscreen wiper circuit, controlling the intermittent (delay) wipe function. It times the pause between wipe cycl...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Washer - 20mm

Clutch Kit is a matched three-piece clutch assembly for the 2.5L 200TDi and 300TDi turbo diesel engines with manual transmission. The kit renews t...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Bolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...

Glow plug TD5

Swivel pin & bracket

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Front Floor Contour Mat Kit is a pair of shaped rubber mats for the front cabin footwells, forming part of the interior floor protection. Each mat...

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Door Hinge - left-hand door hinge that mounts the side door to the body hinge pillar and carries the door as it swings. Steel hinge for the front ...

Steering Box is the recirculating-ball power steering gear at the heart of the steering system, converting rotation of the steering column into the...

Brake Caliper for the rear braking assembly, mounted on the right-hand side. The caliper houses the piston and hydraulic fluid inlet, converting p...

Brake pad fitting kit for STC1277

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Anti-Roll Bar Bush for the anti-roll bar within the suspension stabiliser assembly. The bush locates and insulates the anti-roll bar at its chassi...

Filler cap

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...