Land Rover Parts

Drain plug LT77 R380

Jubilee Clip - 60-80mm is a worm-drive hose clip with a 60-80mm clamping range. The band is tightened by a captive worm screw to secure large-bore...

Joint Washer seals the gearchange/inspection cover against the transfer box casing within the transfer gearbox assembly. Fitted between the cover ...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Coolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Distance piece

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Hex Nut, 3/8" UNF. A general-purpose threaded fastener used at fixing points across the braking, chassis and body assemblies. The 3/8" Unified Nat...

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Drive Belt (V-belt) for the engine accessory drive system, transferring rotation from the crankshaft pulley to a driven accessory. This is a 13 mm...

Lock Washer for the steering box assembly. Fitted beneath a steering box fastener to lock it against rotation, holding the joint secure under stee...

Heater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...

Rear Wiper Blade is the wiping element for the rear wash/wipe system, mounted on the tailgate wiper arm. It clears rain and road spray from the re...

Inlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...

Bonnet Intake Grille Set, finished in satin black with stainless steel mesh, supplied as a matched pair. The grilles fit over the bonnet air intak...

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Brake Fluid for the brake and clutch hydraulic systems, meeting DOT 4 specification and supplied in a 250ml container. This glycol-ether based hyd...

Brake servo assembly for the hydraulic braking system within the Master Cylinder & Servo - Less Anti-Lock Braking System assembly group. This...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Spring Bush - Polyurethane for the leaf spring suspension system on Series Land Rovers. This polyurethane bush fits into the spring eye at the fro...

Grommet

Reverse Lamp forming part of the rear lighting assembly, providing white illumination to the area behind the vehicle when reverse gear is selected....

O-Ring for the Td5 fuel pressure regulator. This O-ring seals the fuel pressure regulator within the Td5 fuel system, maintaining a leak-tight joi...

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Fitment: All models to 1980 except V8

Rear Propshaft for V8 petrol applications, forming part of the drivetrain. It transmits drive from the transfer box rear output flange to the rear ...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Loadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...

Air Intake Duct - Water Separator is a section of the engine air intake on the Td5 2.5L 5-cylinder turbo diesel. It carries intake air from the wa...

This unit provides position illumination at the front of the vehicle and interfaces with the vehicle's electrical lighting circuit and mounting ape...

Track spacer oil seal

Door Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...

Lamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Timing Belt Kit - 200TDi is a timing system service kit for the 200Tdi 2.5L turbo-diesel engine. The kit renews the components that maintain camsh...

Thermostat Housing Gasket seals the joint between the thermostat housing and the cylinder head water outlet in the engine cooling circuit. It main...

Grille Screw Kit - a set of stainless steel fixing screws for mounting the front radiator grille to the body panel. The screws secure the grille a...

Power Steering Reservoir

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...