Land Rover Parts

Door Lock Control Cable is the front-door cable that links the lock mechanism to the door latch, transmitting the locking and unlocking action thro...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Wiper Blade A front windscreen wiper blade within the wiper assembly. It attaches to the wiper arm and clears the windscreen as the arm sweeps acro...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Air Intake Finisher is the wing-top grille that covers the cold air intake aperture of the induction system. This is the right-hand wing-top finis...

Clutch Master Cylinder - 200TDi, VM & V8

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Heater Intake Hose is the flexible convoluted air hose in the heater fresh-air intake ducting. It connects the fresh-air intake to the heater hous...

Mounting Stud

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Wheel Cylinder Repair Kit for overhauling a front drum-brake wheel cylinder with a 1.25 inch bore. It restores the hydraulic seal of a worn or lea...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Wing Nut with a 1/4" BSF thread, tightened by hand without tools. Used to secure the battery clamp frame and the oil-bath air cleaner clamp, where...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Bonnet Release Cable connects the cabin-mounted release lever to the bonnet latch as part of the bonnet locking mechanism. Pulling the interior le...

Water Pump for the 2.25L 4-cylinder engine, operating in the engine cooling circuit. Belt-driven from the crankshaft pulley, the pump circulates c...

Fuel Filler Hose in the fuel tank filler assembly, connecting the filler neck to the tank. It carries fuel from the filler neck into the tank duri...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Spare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Radiator Cap Pressure-relief filler cap for the engine cooling system, sealing the radiator or coolant expansion tank filler neck. Rated to releas...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Service Filter Kit for the 300 Tdi 2.5L turbo diesel engine, grouping the consumable filters and sealing washers required for a routine engine serv...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Coolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Hex Nut, 3/8" UNF. A general-purpose threaded fastener used at fixing points across the braking, chassis and body assemblies. The 3/8" Unified Nat...

Rear door seal RH 110

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...