Land Rover Parts

Wing Nut with a 1/4" BSF thread, tightened by hand without tools. Used to secure the battery clamp frame and the oil-bath air cleaner clamp, where...

Glazing Rubber Seal for retaining glass panels in fixed window aperture frames. This flexible rubber channel seal locates in the groove of the win...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Bonnet Release Cable connects the cabin-mounted release lever to the bonnet latch as part of the bonnet locking mechanism. Pulling the interior le...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Spare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...

Seal

sensor lambda, Sensor-oxygen multi point injection

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...

Radiator Cap Pressure-relief filler cap for the engine cooling system, sealing the radiator or coolant expansion tank filler neck. Rated to releas...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Master Cylinder Nut for the CB-type brake master cylinder, fitted to the end of the cylinder bore. The nut closes and retains the end of the maste...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Plenum Hose - Breather T-Piece to Plenum

Brake Union – a threaded fitting in the hydraulic brake circuit that joins and seals brake pipe. Female union with a 7/16"-20 UNF thread, sized fo...

Gasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...

Heater Inlet Hose is the coolant feed hose supplying the heater matrix in the cabin heating circuit. It carries hot coolant from the engine to the...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Service Filter Kit for the 300 Tdi 2.5L turbo diesel engine, grouping the consumable filters and sealing washers required for a routine engine serv...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Steering Ignition Lock Housing mounted on the steering column, combining the mechanical steering lock with the ignition switch mounting. It mechan...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the brown, thick-secti...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Ignition switch

Rear Door Step Assembly, a spring-loaded folding step forming part of the rear body equipment. It bolts to the rear cross member below the rear end...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

A-Frame Ball Joint Fitting Kit: fitting hardware for mounting the rear A-frame fulcrum bracket and ball joint assembly.

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Front Crankshaft Oil Seal installed in the front cover assembly, part of the engine's crankshaft sealing arrangement. Seals the running clearance ...

Front Bumper Tapping Block and Bolt Set for securing the front bumper, comprising the tapping block and the associated bolt set. The tapping block...

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Hazard Warning Switch, the 12V illuminated rocker switch located on the lower dash switch panel. When pressed it flashes all four direction indica...

Bumper Lamp rear left-hand assembly, part of the rear bumper lighting cluster. The unit combines the reverse lamp and rear fog lamp in a single ho...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Heater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...

Manifold Stud Kit for the 2.25 litre four-cylinder petrol engine, supplying the fixings that mount the exhaust manifold to the cylinder head. Rene...

Gearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...

Instrument Panel Bulb - 12V 3W capless. A push-fit capless bulb for instrument cluster and panel illumination and for low-current warning and indi...