Land Rover Parts

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Rear Lamp Mounting Plinth for NAS-specification rear lamp installations. The plinth forms the raised mounting base that locates the rear lamp unit ...

Heater valve

Valve repair kit

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Double Pipe Clip for the fuel delivery system. This clip locates and retains a pair of parallel fuel pipe runs in a single fixing, holding the feed...

Air flow meter TD5 replacement

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Foam Pad - Air Intake Deflector seals the air intake deflector in the scuttle area, where fresh air is drawn into the heating and ventilation syste...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Windscreen Washer Jet A heated twin-nozzle washer jet that directs washer fluid onto the windscreen. It seats into the scuttle or bonnet panel and ...

Carburettor Spacer for the petrol engine induction system, fitting between the carburettor and the inlet manifold. It sets the carburettor off the...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Flame Trap Hose forming part of the crankcase ventilation (breather) system on the V8 EFI petrol engine. It connects the flame trap T-piece to the...

Window Regulator is the left-hand front door glass mechanism that raises and lowers the window. Part of the door internals, it mounts inside the d...

Rear Door Lock Seal - a gasket for the lock cover plate on the rear end door. It sits between the lock cover plate and the door skin, sealing the ...

Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...

Nut rear suspension arm M13

Shock Absorber - Front - LWB

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Layshaft Bearing for the Series manual gearbox. It supports the layshaft (countershaft) within the gearbox casing, allowing the constant-mesh gear ...

Brake Light Switch mounts on the pedal box and is operated by movement of the brake pedal. When the pedal is depressed the switch closes the stop-...

Flexible Brake Hose for the front hydraulic braking circuit. It carries brake fluid pressure between the rigid chassis-mounted brake pipe and the f...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Throttle body heater assembly OEM

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Drain plug

Clutch Repair Kit for the Land Rover Series III clutch assembly. The kit renews the friction and engagement components of the single dry-plate clut...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Front Propshaft This propshaft transmits drive from the transfer box output to the front axle differential, forming part of the four-wheel-drive d...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Strap

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Lamp Guard - Round - 73mm - a protective guard that fits over a round 73 mm lamp to shield the lens. It clamps over the light unit to protect the ...

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Stud M8 x 25

Suspension Spring U-Bolt for the front leaf-spring suspension, clamping the axle to the spring pack. The U-bolt wraps around the front axle tube a...

Oil Thrower for the drive pinion in the Salisbury axle differential. It fits on the pinion shaft, between the drive flange and the pinion oil seal....

Visco Unit Bearing for the rear propshaft, supporting the viscous coupling unit (VCU) in the four-wheel-drive driveline. The bearing locates on th...

Fuel tank sender and pump assembly Installed within the fuel tank, this unit forms part of the fuel tank pump and mounting assembly and integrates ...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...