Land Rover Parts

Glazing Rubber is the channel rubber that seats the front door window glass within its lift channel, sized to accept 5mm glass. Part of the door g...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Water pump gasket Puma 2.4

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Stub Axle Gasket for the rear axle, fitted between the stub axle flange and the end of the axle case. It seals the joint where the stub axle bolts...

Cylinder Head Bolt for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the engine block, cla...

Oil seal

Tail Pipe is the rear section of the exhaust system, carrying exhaust gas from the silencer to the outlet at the rear of the vehicle. It connects d...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

Brake Hose Kit is a three-hose set of standard-length stainless-steel braided brake hoses that replace the flexible sections of the hydraulic brake...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Accelerator Cable for the 200TDi throttle linkage. The cable runs from the accelerator pedal to the throttle lever on the fuel injection pump. Dep...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Brush set M418G

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Gasket for the carburettor-to-inlet-manifold joint in the induction system of the 2.25L 4-cylinder petrol engine. The gasket fits between the carb...

Steering Box Side Plate Gasket seals the side cover plate against the casing of the manual steering box. It sits between the dowel-located side pl...

Spring bonnet pull cable return

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Window Channel for the front door sliding side window assembly. This aluminium channel runs along the front face of the sliding window and retains...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Bulb - 24V 21W A 24-volt, 21-watt incandescent bulb for the exterior lighting and signalling circuits. Rated for 24V electrical systems, it is a s...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Upgrade your Land Rover Defender or Series vehicle with this complete 73mm LED Light Upgrade Kit. Designed to replace traditional incandescent lamp...

Lamp side repeater RRC

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Front Door Glass Channel Assembly is the run channel that guides the front door window glass within the door frame. It forms part of the front doo...

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Shock Absorber Bush for the front lower shock absorber mounting within the suspension damper assembly. The bush fits at the lower eye of the front...

Rubber Buffer moulded door stop pad fitted within the door check and hinge mechanism. The buffer cushions the door against its check arm and limit...

Brake Servo - Non-ABS - Valve Top Left is the vacuum brake servo in the braking system, providing pedal-assist boost. It sits between the brake pe...

Flanged Bolt - M10 x 50, a Grade 10.9 high-tensile fixing used in the front drive shaft and hub assembly. It secures the drive member (drive flang...

Head Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the joint between the cylinder head and the cylinder block. It seals the comb...

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Air flow meter TD5 replacement

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Exhaust Olive - a conical sealing ring fitted at an exhaust pipe joint, at the silencer-to-tailpipe connection. It seats between the mating pipe s...