Land Rover Parts

Swivel Repair Kit for the front axle swivel assembly, for vehicles fitted with ABS. The kit covers one side of the axle and does not include the sw...

Cubby Box Cup Holder for the centre console cubby box. The holder mounts to the sloping front face of the cubby box, providing a fixed location fo...

Rear Exhaust Silencer forms the rear section of the exhaust system, downstream of the intermediate pipe. It attenuates exhaust noise before the ga...

Clutch Release Bracket mounts within the clutch release mechanism at the gearbox bellhousing, locating and supporting the release components. It p...

Drive Shaft Oil Seal seals the driveshaft output where it passes through the manual transmission casing, retaining gearbox oil at the output interf...

Rear Brake Caliper Carrier for the rear disc brake assembly. The carrier bolts to the rear hub and holds the brake pads, locating the caliper over ...

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Air Suspension Compressor - P38

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Collapsible Salisbury spacer

Distributor Cap for the 2.6 litre 6-cylinder IOE petrol engine, forming the top of the ignition distributor. The rotor arm sweeps inside the cap a...

Rear Bumper Lamp from the rear lighting assembly - the right-hand (RH) unit mounted in the rear bumper. The combined lamp carries the reversing li...

Tailgate latch assembly HCPU

Window Switch

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Fuel Filter & Sedimentor Assembly - Td5

hinge door LH upper with holes for mirror arm. Series 3 and early classic Defender. This is the "smaller" version, used upto (VIN) WA138479 (1998 m...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Windscreen Wiper Wheelbox Spindle Housing for the windscreen wiper rack mechanism. The unit mounts through the bulkhead or scuttle panel and suppo...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Bulkhead Outrigger is a welded structural support bracket in the bulkhead and chassis assembly, tying the base of the bulkhead to the chassis frame...

Track Rod Assembly is the complete steering track rod that links the front wheels across the axle, forming part of the steering linkage. The assem...

Air Filter Element installed in the air cleaner housing of the 200Tdi 2.5L four-cylinder turbo diesel engine. The element filters intake air upstr...

Dzus Fastener is a quarter-turn quick-release stud used to secure the radiator cowl and cooling fan shroud within the engine cooling assembly. The...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

hinge front door RH upper with holes for mirror arm "smaller" version for Series 3 and early classic Defender upto (VIN) WA138479 (1998 model year)

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Ignition heater plug timer glow plug relay

Rear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...

Oil seal 12.5mm OEM

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Rear Body Crossmember is a structural crossmember for the rear floor and body structure, supplied complete with its bolt-on brackets. It spans the...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Barrel Lock & Key is the lock barrel and matching key for the ignition/starter switch. This is the diesel-application barrel for the earlier t...

Front Bumper - a replacement front bumper fitted with integrated Ring LED daytime running lamps. The bumper forms the front-end impact and mountin...

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Bulkhead Outrigger is a structural bracket that supports the left-hand side of the bulkhead and ties it to the chassis frame, carrying the load whe...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Safari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Puma applications. The Torx-head bolts secure the fixing...

Wheel spacer kit fitted between the wheel hub and road wheel within the wheel mounting assembly. The spacers move the wheel mounting face outward...

Horn low note

Exhaust Intermediate Assembly - rear exhaust section for the Discovery 2 4.0L V8 EFI petrol engine, comprising the intermediate pipe and silencer a...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...