Land Rover Parts

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Spark Plug of double-platinum construction for V8 petrol engines, part of the ignition system. The plug delivers the spark that ignites the air-fu...

Door Check Strap - Front - RH

Glazing Rubber is the channel rubber that seats the front door window glass within its lift channel, sized to accept 5mm glass. Part of the door g...

Door Glass Channel (Lift, Front) is the channel fixed along the bottom edge of the front door glass. It grips the lower edge of the window and pro...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Plain Washer - an M8 flat washer fitted under a bolt head or nut. It spreads the clamping load of an M8 fastener across a wider area, protecting t...

Brake Vacuum Pump for the 2.4L TDCi diesel engine, part of the braking vacuum supply. Driven by the engine, it generates the vacuum the brake serv...

Oil Filter - a replaceable oil filter element housed within the engine oil cooler and filter assembly of the 3.0L V6 turbo diesel (TD6) engine. Th...

Transfer Box Hi/Lo Switch is a position switch fitted to the LT230 transfer box. It belongs to the transfer box and four-wheel-drive control circui...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Bonnet Cable is the bonnet release cable linking the cabin release lever to the bonnet latch mechanism. Pulling the interior release lever draws t...

Cylinder Head Bolt for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the engine block, cla...

Tail Pipe is the rear section of the exhaust system, carrying exhaust gas from the silencer to the outlet at the rear of the vehicle. It connects d...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

Bumper Retainer A quarter-turn click-type fastener that secures the bumper and radiator grille panels to the body. It locates through the mounting ...

Filter Kit - 2.2 & 2.4 TDCi for the Land Rover Defender with the Puma TDCi diesel engine. This kit consolidates the main filter and sealing it...

Intermediate Exhaust Pipe in stainless steel, forming the centre section of the Td5 exhaust system. This is a straight-through link pipe fitted in...

Brake Hose Kit is a three-hose set of standard-length stainless-steel braided brake hoses that replace the flexible sections of the hydraulic brake...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Windscreen - a heated, green-tinted laminated windscreen for Puma applications. The heating element embedded in the glass clears frost and condens...

mud flap LH rear (NO LOGO!) Geschikt voor 110" en 130" BEHALVE High Capacity Pick Up (HCPU). Linksachter.

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Raised Air Intake - a steel snorkel that relocates the engine air intake from the inner wing up to roof-line height along the right-hand windscreen...

Accelerator Cable for the 200TDi throttle linkage. The cable runs from the accelerator pedal to the throttle lever on the fuel injection pump. Dep...

Aerial with cable Defender

bar torsion LH

Bolt (M12 x 40, grade 10.9 high-tensile) retains the front brake disc and caliper assembly at the hub. The grade 10.9 rating provides the high cla...

Brush set M418G

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Spring bonnet pull cable return

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Bulb - 24V 21W A 24-volt, 21-watt incandescent bulb for the exterior lighting and signalling circuits. Rated for 24V electrical systems, it is a s...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

LED Lamp Upgrade Kit: 73mm LED lamp units that replace the original bulb-type lamp units.

Lamp side repeater RRC

Fir Tree Clip push-in fastener used to secure interior door casings and trim panels to the body shell. The barbed fir-tree profile is pushed into ...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Front Door Glass Channel Assembly is the run channel that guides the front door window glass within the door frame. It forms part of the front doo...