Land Rover Parts

Crankcase breather T-piece with restrictor V8 EFI

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Thermostat regulates coolant flow within the engine cooling system, with an opening temperature of 82°C. It remains closed while the engine is col...

Water Pump circulates coolant through the engine cooling circuit, drawing from the radiator and feeding the cylinder block and head to maintain ope...

unit adjuster headlamp D1 from FA393361, D2 upto 2A299999.

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Main Bearing Set for the 2.25-litre 4-cylinder engine in its 3-main-bearing form. These are the replaceable shell bearings that carry the crankshaf...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Lower Steering Shaft Assembly forming the intermediate link in the steering column, connecting the lower steering column to the steering box input ...

Master Lighting Switch mounted on the steering column, providing the primary control for the side lights and headlamps. It forms part of the steer...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Air cleaner element installed in the air cleaner housing of the engine intake system, where it filters incoming air before it enters the intake duc...

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Fitment Classic Defender: All diesel models up to (VIN) FA375497 (including Turbo Diesel, NOT for TDI) All petrol models except V8 up to (VIN) FA...

Anti-Roll Bar Bush for the rear suspension. This rubber bush insulates the rear anti-roll bar at its chassis mounting, allowing the bar to rotate u...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Spring Seat for the front coil spring suspension. It forms the lower seat that locates and supports the base of the front coil spring on the axle, ...

Spin-on engine oil filter installed in the oil filter housing of the engine lubrication system, on the 2.2L TDCi diesel engine. The filter element...

Hub Bearing – inner taper roller bearing for the front and rear wheel hubs. The bearing sits inside the hub and runs on the stub axle, carrying th...

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Clutch release fork is used in the clutch release mechanism of manual transmission systems. The fork operates within the clutch housing and conve...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Track Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...

Window Channel

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Alternator Pulley mounts on the alternator drive shaft and is turned by the engine drive belt. It transfers rotation from the crankshaft belt driv...

Rear Shock Absorber provides damping control on the rear axle for suspension set up with approximately 50 mm of additional travel. Twin-tube const...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Centre Exhaust Silencer for the Discovery 2 TD5 2.5L five-cylinder diesel engine. This silencer forms the middle section of the three-part exhaust...

Track Rod Assembly for the Range Rover P38 steering linkage. This assembly connects the two front wheel hubs across the front axle, maintaining co...

Caliper Bolt for the front brake caliper assembly. This bolt secures the brake caliper to the hub carrier. It is a critical fastener in the front ...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Rear Anti-Roll Bar Bolt secures the rear anti-roll bar within the rear suspension assembly. It fixes the bar to its mounting, holding it in positi...

U-Bolt for the rear leaf-spring suspension of long-wheelbase (LWB) models. The U-shaped bolt passes over the axle and clamps the rear leaf-spring ...

Anti-Squeal Shim is a thin damping shim for the rear disc brake assembly. It fits between the brake pad backing plate and the caliper piston, isol...

Heater Hose for the front of the heater circuit, carrying engine coolant between the engine feed and the heater unit. This flat-section hose forms...

Heater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Wiper linkage (140 degrees)

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Lock Washer fitted under a nut or bolt head to resist loosening from vibration. An M10 shakeproof (external-serrated) washer. The serrated teeth b...