Land Rover Parts

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Track Rod Assembly for the Range Rover P38 steering linkage. This assembly connects the two front wheel hubs across the front axle, maintaining co...

Rear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...

Caliper Bolt for the front brake caliper assembly. This bolt secures the brake caliper to the hub carrier. It is a critical fastener in the front ...

Mirror Head - 195 mm x 145 mm. The rectangular exterior mirror head that fits the bar-type mirror arm, providing the driver's rearward view along t...

Rear Anti-Roll Bar Bolt secures the rear anti-roll bar within the rear suspension assembly. It fixes the bar to its mounting, holding it in positi...

Rocker Shaft Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the rocker shaft assembly to the cylinder head. It clamps the rocker s...

Plain Nut - an M10 threaded fastener used at engine and chassis fixing points. Applications include retaining the shock absorber mountings to the ...

Power Steering Belt - polyvee (multi-rib) drive belt that drives the power-assisted steering pump. Runs in the auxiliary drive, transferring rotat...

Clutch Pedal Torsion Spring is a return spring for the clutch pedal, fitted within the pedal box assembly on manual transmission vehicles. It prov...

Half Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Brake Pipe for the front braking hydraulic circuit. This is the flexible pipe that feeds the front wheel cylinders. It connects the chassis-mounte...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Collapsible Salisbury spacer

Brake Hose for the rear of the braking hydraulic circuit, in non-ABS applications. This flexible hose carries hydraulic pressure from the rigid br...

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Brake master cylinder (single line with servo)

Wiper linkage (140 degrees)

Water Temperature Sensor (coolant temperature transducer) that threads into the thermostat housing within the engine cooling circuit. The transduc...

Oil Thrower for the drive pinion in the Salisbury axle differential. It fits on the pinion shaft, between the drive flange and the pinion oil seal....

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Lock Washer fitted under a nut or bolt head to resist loosening from vibration. An M10 shakeproof (external-serrated) washer. The serrated teeth b...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

U-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...

Ignition Switch - Petrol - Steering Column is the electrical ignition and starter switch mounted in the steering column, forming part of the igniti...

Interior Courtesy Lamp is the cabin roof light unit within the interior lighting circuit, providing illumination of the vehicle interior. The unit...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Filter and housing D2 TD5

Bonnet Catch Ferrule Kit for the cable-operated bonnet release mechanism. The kit renews the trunnion (ferrule) and threaded fitting that anchor t...

Oil Pump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the oil pump to its mounting face on the engine. It forms the oil-tight j...

Door Sill Seal – Front is the lower weatherstrip fitted along the bottom edge of the front door aperture. It forms a weather barrier at the base o...

Spring Retention Ring for the front coil-spring suspension. It clamps the upper end of the road spring, securing it against its seat on the chassis...

Anti-Rattle Spring for the front disc-brake caliper. It holds the brake pads under light tension inside the caliper, taking up free play so the pad...

Front door window regulator forming part of the door glass operating assembly, responsible for controlled raising and lowering of the electric wind...

Oil Filler Cap Assembly for the rocker (valve) cover of the 2.25L 4-cylinder petrol engine. The cap seals the oil filler neck and incorporates an i...

Flanged Head Bolt, M8 x 25mm. A hex-head bolt with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Split Pin used to secure the accelerator cable and hand throttle cable connections, retaining the clevis pin at the cable-to-linkage joint. After ...

Window Catch Gasket seals the window catch on the rear side door. It fits between the window catch and the door panel, forming a weatherproof seal...

Service Filter Kit gathers the filters required for a routine engine service on the 2.5-litre diesel, in both naturally aspirated and turbo diesel ...

Reverse Light - a 95mm round rear reversing lamp with a clear lens and LED illumination. It forms part of the rear lamp arrangement, projecting wh...

Light Guard Set - Rear Hinged rear lamp guard set that protects the rear lamp lenses from stone strike and low-speed impact during off-road use. T...

Radiator Assembly for the Td5 2.5L 5-cylinder turbo diesel engine cooling system. The radiator is the primary heat-exchanger in the coolant circui...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Parabolic Leaf Spring for the rear axle, supplied as a matched pair. A parabolic spring uses fewer, tapered leaves than a conventional multi-leaf ...

Auxiliary Fuel Tank for the fuel storage system, in the original military pattern. This under-seat auxiliary petrol tank supplements the main fuel...