Land Rover Parts

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Radiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...

Rear Reverse Lamp - LED, Smoked - 95 mm LED reversing lamp with a smoked lens, supplied as a direct replacement for the standard rear reverse lamp....

Pollen & Odour Filter - the cabin air filter in the HVAC intake system. It sits in the fresh-air path upstream of the blower, cleaning the air ...

Windshield wiper arm D2 LHD

Rear Door Gas Strut - a gas-assisted check stay that replaces the original mechanical door stopper on the rear (side-hung) door of Td5 and Puma (TD...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Plug

Cylinder Head Gasket for the Rover V8 petrol engine, sealing the joint between one cylinder head and the engine block. It seals the combustion cha...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Fuel and Exhaust System Cleaner (Cataclean) is a fuel-borne additive that clears carbon deposits from the fuel and exhaust systems of petrol engine...

Gasket kit 300tdi lower block set no rear crankshaft seal

Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...

Front Wheel Hub and Bearing Assembly is the pre-assembled hub unit at the front axle, combining the wheel hub, its bearing and the ABS wheel speed ...

Rear shock absorber

Brake caliper 110/130 LH rear

Brake Caliper - Rear - RH

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Washer Adjusting washer for the rear suspension arm mounting. Part of the rear multi-link suspension assembly, it locates at the suspension arm pi...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...

Shock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Bolt wishbone OEM

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Coolant Hose - Radiator Upper is the upper hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries hot coolant from...

Engine mounting

Radiator Rubber Mount for the engine cooling system. This rubber mounting locates the radiator in its support panel and cushions it against engine ...

Hinge Packer Shim for the door hinge assembly. Fitted between the hinge and its mounting face to set door alignment. Adding or removing shims adju...

Ignition Lead Set is a complete set of high-tension (HT) leads for the ignition system of the 2.6L six-cylinder petrol engine. The leads carry hig...

Steering Damper Assembly for the front axle steering linkage. The hydraulic damper mounts across the steering linkage, where it controls lateral o...

Blanking Plug Grommet for the dash assembly. This rubber plug fills an unused aperture in the dash panel - such as the opening for the hand throttl...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Tailgate Gas Strut - Upper for the rear split tailgate, supporting the upper lift-up section of the door. The gas-charged strut counterbalances th...

Master Lighting Switch mounted on the steering column, providing the primary control for the side lights and headlamps. It forms part of the steer...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Rear Stop and Flasher Lamp for installation in the left-hand position of the rear bumper. This unit provides the stop lamp and direction indicator...

Service kit for the front axle swivel housing assembly used on non-ABS axle configurations. The swivel housing forms the pivot joint between the ...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Inlet & Exhaust Manifold Gasket - 300TDi

Radius Arm Bush - Front for the front suspension radius arm assembly. This rubber bush is pressed into the forward end of the front radius arm and...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Window Channel

Crankshaft Oil Seal - Rear - Heavy Duty for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal hou...

Military red rear stop light lens

This steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...