Land Rover Parts

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 200 TDi 2.5L turbo diesel engine. It forms a coolant-tight...

Window Regulator Escutcheon - trim finisher that locates over the manual window winder spindle on the inner door, concealing the regulator aperture...

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Plenum hose

Key Features & Benefits: Color: Black Fitment: Suitable for Land Rover Series models Standard Design: Non-adjustable seat base offering s...

Brake pipe

Trunnion kit

Exhaust Valve for the Rover V8 EFI petrol engine, fitted in the cylinder head valvetrain. The valve seals the exhaust port during the combustion c...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Clevis Pin - a linkage pin used in the accelerator and throttle control. It joins the throttle cable clevis to its operating lever, allowing the l...

Selector Detent Spring is part of the gearbox gear-selection detent for the forward-gear selector shafts (1st/2nd and 3rd/4th). It loads the deten...

Headlamp Surround — the chrome bezel that trims and retains the outer edge of a 7-inch round headlamp. A polished chrome ring fitted over the head...

Spring nut

Nut M16 hex nut for the front anti-roll bar assembly. Secures the front anti-roll bar (stabiliser bar) to its mounting link on the suspension.

Cam Cover Gasket for the 2.4L Duratorq TDCi (Puma) diesel engine, sealing the camshaft cover to the cylinder head. It forms the oil-tight joint be...

Oil Filter Adaptor Gasket Seals the oil filter adaptor housing to the cylinder block within the lubrication circuit of the 300 TDi 2.5L diesel engi...

Rear wiper motor

Heater Control Valve regulates the flow of engine coolant into the heater matrix, forming part of the cabin HVAC heating circuit. The valve is cab...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Bolt - Torx - Countersunk - Rear Door Hinge is a countersunk Torx-head bolt used to secure the rear side door hinge and check strap. It retains th...

Bolt - Front Radius Arm is the M16 x 100 mm grade 10.9 high-tensile bolt that secures the front radius arm within the front suspension linkage. It...

Sealing O-Ring for the joint between the flywheel housing and the engine block on the 2.25L 5-bearing petrol and 2.5L naturally-aspirated diesel en...

Clamp tube GENUINE LR for pipe EGR 2.7 TDV6 and 3.0 TDV6

Handbrake Shoe - V8 - LT95 is a brake shoe for the transmission-mounted parking brake used with the LT95 four-speed gearbox. Rather than acting at...

Cooling Fan Assembly drives airflow through the radiator within the engine cooling system, supplied complete with the fan drive. The integrated vi...

Torsional Vibration Damper mounting on the crankshaft nose of the 200Tdi 2.5L four-cylinder turbo diesel engine. Also serving as the crankshaft pu...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Cylinder Head Bolt Washer for the 2.25L and 2.5L 4-cylinder petrol and diesel engines. It fits under the head of each cylinder head bolt, spreadin...

Injector Leak-Off Pipe for the 2.25L and 2.5L naturally-aspirated diesel fuel injection circuit. This spill-return pipe connects the return unions ...

Brake Hose Kit is a set of four +40mm extended stainless-steel braided brake hoses, one for each wheel, replacing the flexible sections of the hydr...

Ball Joint Service Tool for the steering drop-arm ball joint. The tool presses the drop-arm ball joint (part RBG000010) into and out of the drop a...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Ignition Condenser for the contact-breaker distributor, of the Ducellier type. Wired across the contact-breaker points, the condenser absorbs the ...

Spring Isolator - Front, Upper for the front coil spring in the suspension. The isolator is the elastomer pad that sits between the top of the fro...

Clutch Hose for the hydraulic clutch actuation system. This flexible hose provides the hydraulic connection between the rigid clutch pipework and t...

Door Check Strap Torsion Bar forms part of the side door check-strap mechanism, providing the sprung resistance that holds the door at its intermed...

Top radiator hose - RR L322 V8

Cooling Fan for the 2.5L 300 TDi turbo diesel engine, forming part of the engine cooling assembly. The fan is driven from the front of the engine ...

Caged Nut - a captive plastic nut that receives a self-tapping or trim screw. It clips into a panel aperture to provide a fixed threaded seat, use...

Alternator for the engine charging circuit, of the Lucas A127 type rated at 45A output. Driven by the auxiliary drive belt from the crankshaft pul...

Repair kit for clutch master cylinder, fits to AEU1714, ANR2651.

Bleed Screw for the coolant bleed point on Td5 engines. The screw seats in the bleed port on the top coolant hose and is opened to release trapped...

Bottom hose

Heater Hose - the inlet hose in the heater coolant circuit on the V8 twin-carburettor petrol engine. It carries hot coolant from the engine to the...

Lock Nut is a self-retaining fastener used in the door latch and lock mechanism. Part of the door locking hardware, it secures the latch and lock ...

Cylinder Head Bolt (Short) for the V8 petrol engine, securing the cylinder head to the engine block. This is the shorter of the two head bolt leng...

Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...