Land Rover Parts

Condenser incl. fan Defender

Clutch gasket

Hazard Switch - the push-type dashboard switch that operates the hazard warning function. When pushed it flashes all four indicator lamps together ...

Core Plug seals a casting aperture in the cylinder block or head of the 2.25L and 2.5L four-cylinder petrol engines. Also known as an expansion or...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Rear Mudflap for the left-hand side, part of the exterior underbody protection assembly. Fitted behind the rear wheel, it shields the lower rear b...

O-ring

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Heater Control Bulb illuminates the heater and ventilation control panel. Fitted into the front HVAC control assembly, it backlights the heater co...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the green, thin-sectio...

Washer for the non-hinged windscreen frame assembly. It seats on the frame fixings, spreading the fastener clamp load across the mounting surface ...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Spring Retainer - Rear is the rear coil spring seat retainer plate in the rear suspension. It locates and holds the rear coil spring at its seat, ...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Headlamp Wash T-Piece - three-way T-connector in the headlamp washer fluid line. Splits the feed hose from the washer pump so a single supply serv...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Cylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...

Polyurethane Rear Upper A-frame suspension link bush set (NTC1773), chassis end.

Mudflap – Rear – RH is the right-hand rear mudflap, fitted behind the rear wheel to reduce road spray and protect the bodywork from mud and stone t...

Bolt - 5/16" UNF x 1/2" - a hex-head set screw with a 5/16" UNF (Unified National Fine) thread and 1/2" length. Fully threaded to the head, it pro...

Shock Absorber for the front axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative ...

Door Vertical Filler for the door sealing trim. This vertical rubber filler closes the gap at the rear edge of the front doors and at the front and...

Bolt - a threaded fastener used within the axle and suspension assembly. It secures front axle case mountings and rear suspension arm attachments,...

Exhaust Valve - the poppet valve that seals the exhaust port in the cylinder head and opens on the exhaust stroke to release spent combustion gases...

Power Steering Suction Hose for the power steering hydraulic circuit. This low-pressure hose carries fluid from the reservoir to the inlet of the p...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Brake Master Cylinder within the Master Cylinder & Servo assembly, fitted to non-ABS braking configurations. This hydraulic component converts...

Lock Striker is the anti-burst striker plate for the rear door latch assembly. It is mounted to the body aperture and provides the engagement point...

Shock Absorber Bolt secures a shock absorber to its mounting in the suspension. The long shank passes through the damper eye and mounting bracket ...

Brake Pipe carries hydraulic pressure along the chassis within the braking hydraulic circuit, routing from the front to the rear of the vehicle on ...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Shock Absorber for the rear suspension, forming part of the rear axle damping assembly. This telescopic hydraulic damper is fitted between the cha...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 4-1/2" shank length. A long-shank hex-head fastener for general assembly and fi...

Decoke Gasket Set for the 3.5L V8 petrol engine with twin carburettors. The set supplies the gaskets needed when the cylinder heads are removed fo...

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Brake Master Cylinder Repair Kit for the non-ABS brake master cylinder. The kit renews the internal seals when the master cylinder is overhauled, ...

Interior switch

Upper Classic Speedo Cable - 90/110

Coolant Hose - Radiator Bottom is the lower hose in the engine cooling circuit. It carries cooled coolant from the radiator bottom outlet back to ...

Clevis Pin for the front door hinge and check strap assembly. This pin secures the door check strap (travel limiter) at its pivot, retaining the s...

Exhaust pipe V8 EFI

Choke Cable operates the carburettor choke from the driver's control within the fuel and cold-start system, for V8 carburettor applications in left...

Chassis Frame Grommet for the vehicle chassis. This grommet plugs an aperture in the box-section chassis rail, sealing the opening against the ingr...

Front Outer Seat Base for the cab front seating, supplied complete and assembled with a black vinyl cover. It forms the lower seat cushion of the ...