Land Rover Parts

Carburettor Repair Kit for the six-cylinder petrol engine carburettor. It supplies the renewable service parts used to overhaul the carburettor and...

Gear Change Selector Shaft Spring A spring for the gearbox gear-change selector mechanism. It acts on the selector shaft to provide the spring loa...

Exhaust Tailpipe Silencer for the right-hand side of a twin (dual) exhaust system. Forms the rearmost section of the exhaust, attenuating gas-flow ...

CLUTCH KIT - COVER + PLATE + BEARING - TD5 - D2/DEF 83-06

LWB voorste ophangpunt van achterste veer LH en RH

Front Brake Shoe Set for the front drum brakes. The brake shoes carry the friction linings that are forced outward against the brake drum by the w...

ABS Sensor for the front wheel of the anti-lock braking system. This wheel speed sensor monitors rotational speed at the front hub and signals it ...

ABS Wheel Speed Sensor - Front for the 4-wheel ABS braking system. Mounted at the front axle, the sensor reads a toothed reluctor ring and generat...

Rear Chassis Extension (Long), a structural repair section for the rear of the ladder-frame chassis. It renews the rearmost length of the chassis ...

Fuel Filter for the diesel fuel supply system of the 2.2L DW12 common-rail direct-injection turbo diesel engine. It is fitted in the fuel line betw...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Exterior Door Handle for the front right-hand door, right-hand drive configuration. Mounted on the outer door skin, the handle forms part of the e...

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

Brake Caliper Seal Kit for the front hydraulic braking circuit, supplying the seals required to reseal a four-piston front brake caliper. The seal...

Stainless Braided Brake Hose Kit for the flexible sections of the hydraulic braking circuit, made to imperial thread specification and extended by ...

Crankshaft Timing Sprocket mounts on the nose of the crankshaft and forms part of the timing drive. Its teeth engage the timing chain to drive the...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Upper Rear Tailgate Crossmember is the structural member spanning the top of the tailgate aperture, forming the upper edge of the rear body opening...

Fuel Pipe from the Td5 2.5L 5-cylinder turbo diesel fuel system, running on the low-pressure side between the inline fuel filter and the pump. It ...

Filler pipe hose 90

Exhaust tailpipe silencer P38 dual LH

Rear Reflector a passive retroreflective marker mounted at the rear of the vehicle. It reflects the headlights of following traffic so the rear of...

Heater Matrix is the heat exchanger within the heater assembly of the cabin HVAC system. Hot engine coolant is circulated through the matrix while...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Lock Nut used to secure interior trim components, including the carpet and sill finishers and the associated bodyside and dust seals. The hex nut ...

Coolant Hose connects the coolant rail to the coolant pump, carrying coolant between the rail and the pump inlet within the cooling circuit. Fitte...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Shim plate

Brake Master Cylinder of the metric AP type, the hydraulic heart of the braking system. Mounted on the brake servo, the master cylinder converts t...

Fuel Tank Sender mounts in the fuel tank and signals the fuel level to the dashboard gauge, forming part of the fuel level sensing circuit. A floa...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Front Sill Panel for the right-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clo...

Gearbox Tunnel Insulation Pad - heat and sound insulation pad fitted to the gearbox tunnel around the gear lever. For manual transmission applicat...

Heater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Clutch gasket

Radius Arm Bush - front radius arm mounting bush at the chassis end of the arm. It locates and insulates the radius arm where it attaches to the ch...

Camshaft Lock Washer retains the camshaft gear securing bolt at the front of the camshaft, part of the engine timing drive. After the bolt is tigh...

Hazard Switch - the push-type dashboard switch that operates the hazard warning function. When pushed it flashes all four indicator lamps together ...

Pipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...

Core Plug seals a casting aperture in the cylinder block or head of the 2.25L and 2.5L four-cylinder petrol engines. Also known as an expansion or...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Output shaft bearing

O-ring

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...