Land Rover Parts

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Shock absorber bush (eye), anti roll bar bush

Headlamp Bowl Kit for the 7-inch headlamp assembly on Series III and Defender vehicles. This kit comprises the plastic headlamp backing bowl and t...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Rear Lamp Loom Harness Extension for the exterior lighting circuit. A two-pin extension harness that lengthens the wiring run between the main bod...

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Brake Cleaner in a 500ml aerosol can, for removing brake dust, oil, grease, and sooty deposits from braking components and engine housings. Fast-e...

Front Door Seal fitted to the body aperture of the right-hand front door, forming part of the door perimeter sealing system within the body closure...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Drum Brake Shoe Set covering one full axle. The shoes carry the friction linings that press outward against the brake drum to slow the wheel when t...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Drum Brake Shoe Set covering one full axle. The shoes carry the friction linings that press outward against the brake drum to slow the wheel when t...

Spring Washer, 1/4" nominal size. A split helical washer fitted under a nut or bolt head as a fastening hardware component. The sprung split appli...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

O-Ring - a static seal for the outer drive shaft hub assembly. It seals the joint between the drive shaft flange and the outer hub, preventing lubr...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Starter Solenoid Relay for 12V petrol engines, acting as a high-current switching relay in the starting circuit. When energised by the ignition sw...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Crankshaft Rear Oil Seal Kit - Cork for the rear crankshaft sealing assembly on Series Land Rover engines with a 3-bearing crankshaft. This kit su...

Major Service Kit for the 2.5L Td5 engine, containing the filtration and service consumables for a full scheduled service. Kit contents: 1 x oil f...

Fuel Connector Block Strainer O-Ring for the Td5 2.5L 5-Cylinder diesel engine. This O-ring seals the strainer within the fuel connector block, pr...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Instrument Voltage Stabiliser - a thermal bimetallic unit mounted on the back of the instrument cluster that regulates the supply voltage to the fu...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Front Bumper Tapping Plate fitted behind the front bumper mounting points, providing a reinforced steel backing surface for the bumper fixing bolts...

Zenith Carburettor Overhaul Kit for the Zenith 36IV carburettor on 4-cylinder petrol engines. This is the complete overhaul kit for the Zenith 36I...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Clutch Hose - flexible hydraulic line in the clutch actuation circuit. Carries hydraulic fluid from the rigid pipe run to the clutch slave cylinde...

Rear Wiper Blade, 14 inch, for the tailgate wiper system on the Discovery 2. This blade fits the rear wiper arm and provides the rubber wiping con...

Brake master cylinder LWB post-80

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Fuel Filler Cap for the fuel tank filler neck, part of the fuel storage and filler assembly. Threads onto the filler neck to seal the fuel tank af...

Brake Shoe Set for the front drum brake assembly, supplied as a complete axle set of four shoes covering both front wheels. Each shoe carries the ...

Windscreen Aperture Glazing Rubber, the weatherseal that sits between the windscreen glass and the body aperture, forming the primary sealing inter...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...