Land Rover Parts

Ignition Coil A high-output sports coil for the ignition circuit. It sits between the low-tension supply and the distributor, converting the primar...

Track Rod Clamp Kit secures the track rod within the steering linkage assembly, holding the joint in position so the steering geometry stays set. ...

Door aperture sealing rubber supplied in a continuous 30 metre roll for use within the body sealing system. This profile installs along the door a...

Reverse Light Switch for the R380 5-speed manual gearbox, completing the reverse lamp circuit when reverse gear is engaged. This switch threads in...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

double washer, restrictor

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

Plain Washer - Metric M5, used across a wide range of Land Rover fixings applications. A standard metric M5 plain washer for load distribution und...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Heater O-Ring seal for the heater circuit. Seals a heater pipe or matrix connection against coolant leakage. Sold individually.

Rear Brake Caliper Seal Kit for rebuilding both rear brake calipers on the Discovery 2 and Range Rover P38, supplied as a pair to cover both sides ...

Injector O-Ring is the lower sealing ring for a diesel fuel injector, used on 3.0L SDV6 and 4.4L TDV8 engines. It seals the lower body of the inje...

Door Hinge Nut Plate - a threaded anchor plate for the rear side door hinge. The plate sits behind the body panel at the door hinge mounting and p...

Air Intake Hose forms part of the engine air intake ducting. It carries filtered air from the air cleaner housing to the throttle body and inlet ma...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Drip Rail Side is a side roof drip rail finisher, part of the exterior body trim running along the roof edge. Fitted above the door aperture, it c...

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Brake caliper piston rear

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Banjo Bolt - the hollow union bolt that secures the external oil feed pipe to the cylinder head within the engine lubrication circuit. It clamps t...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Disc brake

Stud for the front axle swivel pin housing - a threaded stud that provides a fixed anchor for fastening a mating component to the swivel pin housin...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Injector Nozzle is the atomising tip of the diesel fuel injector, sitting in the fuel injection circuit between the injector body and the combustio...

Lamp Guard for 95mm NAS round lights fitted to Defender models up to 2016. Designed to protect the larger-diameter 95mm North American Specificati...

PAS pump assy Disco 2 TD5

Polyurethane Suspension Bush Kit - a full-vehicle set of replacement suspension bushes for the Series 3 long-wheelbase (109") chassis, supplied in ...

Thermostat regulates coolant flow through the cooling circuit, holding the coolant in the block until operating temperature is reached and then ope...

Driveshaft Spacer - a 15.5mm spacer used within the front and rear axle drive shaft and hub assembly. The spacer sits between the drive shaft and ...

Wiper Blade - Front is part of the front windscreen wiper assembly. The blade clips onto the front wiper arm and sweeps across the windscreen to m...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Bracket tie bar for steering box

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Throttle Body Gasket seals the throttle body to the plenum chamber on the 4.0L and 4.6L V8 EFI petrol engine. Fitted between the throttle body and...

Contact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...

Top Coolant Hose for the engine cooling circuit. Carries hot coolant from the engine outlet at the thermostat housing to the top tank of the radia...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Intercooler Hose Kit - Silicone Blue for the turbocharger and intercooler charge-air circuit on the Td5 2.5L 5-cylinder turbo diesel engine. The k...

Heater To Bulkhead Seal seals the joint between the heater and blower duct and the bulkhead aperture, within the heating and ventilation assembly. ...

Drop Arm Nut secures the steering drop arm onto the splined output (sector) shaft of the steering box. This is the nyloc retaining nut for the dro...