Land Rover Parts

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings

Repair kit KIT-POWER ASSISTED STEERING BOX SEAL

Glazing Seal - the glazing rubber that lines the front door window channel and cushions the glass within it. It grips the edge of the glass, holds ...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Sealing Washer for the fuel injector, part of the diesel fuel injection system. The washer seats between the base of the injector and its bore in ...

Front Door Seal Kit re-seals the right-hand front door aperture, supplied with the rivets needed to fit it. The kit contains six door sealing rubb...

Sealing ring

Brake Master Cylinder, CB type, converting brake pedal effort into hydraulic pressure for the wheel cylinders. The CB type is identified by the nu...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Power Steering Pipe for the power-assisted steering hydraulic circuit, carrying pressurised fluid between the steering pump and the steering box. ...

Radiator Top Hose in the engine cooling circuit, connecting the radiator to the upper coolant pipe. It carries heated coolant from the engine's up...

Temperature sensor

Cellular Dynamic Shock Absorber A long-travel rear damper that controls axle movement within the suspension, mounted between the chassis and the re...

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Fuel Filler Tube forming the neck of the fuel tank filler system. It carries fuel from the filler cap opening down into the tank during refuelling...

Shroud clamp

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, converting pressurised fluid from the clutch master cylinder into me...

Bonnet Release Cable is the Bowden control cable that links the in-cab release lever to the bonnet latch mechanism. Pulling the release lever draw...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Rear high mounted brake lamp / stop lamp

Exhaust Clamp for the V8 engine exhaust system, securing a front-pipe joint. The clamp draws two pipe sections together at their slip joint, holdin...

Rocker Cover Gasket sealing the inlet rocker cover to the cylinder head on the 2.0L petrol IOE (Inlet Over Exhaust) engine. Fitted between the upp...

Washer Dowty sealing washer for the Active Cornering Enhancement (ACE) hydraulic anti-roll system. It seals the pipe-to-actuator union, fitting at...

Coolant Hose - Radiator to Oil Cooler is a moulded coolant hose within the engine cooling circuit. It carries coolant between the radiator and the...

Window Channel - the top section of the front door glass run channel. It runs along the upper edge of the door frame and guides the top of the wind...

Timing Chain for the 2.25L and 2.5L four-cylinder petrol engines with the five-bearing crankshaft, running inside the front timing cover. It drive...

Intercooler Hose forms part of the turbocharger charge-air circuit, connecting the intercooler outlet to the inlet manifold. It carries cooled, pr...

Bonnet Buffer Defender 2007 on

Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...

Differential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...

Dowel A locating dowel for the engine cylinder block and cylinder head assembly. It seats in machined bores to align the cylinder head to the bloc...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Sealing Washer seals the timing chain tensioner at the point where it threads into the engine, forming a leak-tight joint at the tensioner mounting...

Hose Clamp secures a flexible hose onto a rigid spigot or stub and seals the joint against leakage. It belongs to the hoses and connections group. ...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Gasket - Transfer Box Gearchange Housing Plate

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Clutch Withdrawal Unit Gasket - seals the mounting joint where the clutch withdrawal (release) housing bolts to the gearbox bellhousing. Part of t...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

In/out member

Steering Box Assembly - LHD is the power-assisted recirculating-ball steering box, in the left-hand-drive configuration. It is the central unit of...