Land Rover Parts

Crankshaft Timing Sprocket mounts on the nose of the crankshaft and forms part of the timing drive. Its teeth engage the timing chain to drive the...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Bulkhead Mounting Bolt - M12 x 180mm fastener securing the lower bulkhead to the chassis. Forms part of the body-to-chassis mounting at the base o...

Upper Rear Tailgate Crossmember is the structural member spanning the top of the tailgate aperture, forming the upper edge of the rear body opening...

Filler pipe hose 90

Exhaust Downpipe - De-Cat for the front section of the exhaust system, fitted downstream of the turbocharger outlet on TD5 diesel applications. Th...

Water Drain Plug for the Td5 2.5L 5-cylinder turbo diesel cylinder head, part of the engine cooling circuit. It seals the coolant drain point in t...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Coolant Hose connects the coolant rail to the coolant pump, carrying coolant between the rail and the pump inlet within the cooling circuit. Fitte...

Shock Absorber Bush Set (4) - Rear Upper - Polyurethane is the upper mounting bush for the rear shock absorber, where the damper attaches to its bo...

Shim plate

Centre Exhaust Silencer located in the mid-section of the V8 exhaust system, between the front downpipe assembly and the rear silencer. Designed f...

Brake Master Cylinder of the metric AP type, the hydraulic heart of the braking system. Mounted on the brake servo, the master cylinder converts t...

Fuel Tank Sender mounts in the fuel tank and signals the fuel level to the dashboard gauge, forming part of the fuel level sensing circuit. A floa...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Front Sill Panel for the right-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clo...

Gearbox Tunnel Insulation Pad - heat and sound insulation pad fitted to the gearbox tunnel around the gear lever. For manual transmission applicat...

Heater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Circlip Retaining circlip for the gearbox rear output shaft. It seats in a machined groove on the output shaft, locating the adjacent component ax...

Radius Arm Bush - front radius arm mounting bush at the chassis end of the arm. It locates and insulates the radius arm where it attaches to the ch...

Camshaft Lock Washer retains the camshaft gear securing bolt at the front of the camshaft, part of the engine timing drive. After the bolt is tigh...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Engine Lifting Bracket bolts to the cylinder head and provides a rated attachment point for hoisting the engine. Fitted to the four-cylinder petro...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Air Suspension Pin is a retaining pin within the air suspension assembly, securing the front air spring at its mounting.

Mudflap Bracket for the rear left-hand position, the bracket that mounts the rear mudflap to the body behind the wheel. It holds the mudflap (spla...

Plenum Chamber Hose Hose within the V8 EFI induction system, running from the plenum chamber to the starter motor housing. It connects the plenum ...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Windscreen Bracket Spacer is a packing piece used in the windscreen mounting assembly, seating between a fixed windscreen bracket and its body moun...

Dial Illumination Bulb for the climate control panel, providing backlighting for the heating and ventilation controls. It seats behind the switch ...

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Mud Flap for the left-hand side, covering both the front and rear wheel positions. Part of the exterior body protection. Fitted behind the wheel a...

Front Screen Timer Relay is the grey timer relay within the heated front windscreen circuit. When the heated screen is switched on, this relay ene...

Radiator Grille - the front grille panel that fits in the front body aperture ahead of the radiator. It admits cooling airflow to the radiator whi...

Timing Chain Tensioner for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The tensioner...

Rod LHD

This special nut (thread size M14) is used in the rear suspension system across several Land Rover and Range Rover models. It plays a crucial role ...

Contact Set for the distributor of the 2.25L petrol engine, 24V FFR (Fitted-For-Radio) military specification with screened ignition. The contact ...

Spark Plug for the engine ignition system. It threads into the cylinder head so its electrodes sit in the combustion chamber, where the spark ignit...

Wheel Nut for securing an alloy road wheel to the hub. It threads onto the wheel stud and clamps the wheel against the hub mounting face, providing...

Turbo Oil Drain Pipe for the 300 TDi engine, returning lubricating oil from the turbocharger to the sump. Connects the turbocharger bearing housin...

Ensure the secure and hassle-free lowering and raising of your spare wheel with this spare wheel winch, designed for Land Rover models with an unde...