Land Rover Parts

Heater Blend Motor Servo for the HVAC air-distribution housing. The servo drives the blend flap that sets the ratio of hot to cold air, regulating ...

Brake Caliper for the left-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the piston...

Brake Caliper for the right-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the pisto...

A-Post Trim is the interior trim panel that covers the A-pillar (the windscreen pillar), concealing the body structure and any wiring routed throug...

Air Filter Element for the engine air intake system, seated within the air cleaner housing. The element traps dust and airborne particles from the...

Injector O-Ring is the lower sealing ring for a diesel fuel injector, used on 3.0L SDV6 and 4.4L TDV8 engines. It seals the lower body of the inje...

Body blanking plug 12 X 18MM

Air Intake Hose forms part of the engine air intake ducting. It carries filtered air from the air cleaner housing to the throttle body and inlet ma...

Drip Rail Side is a side roof drip rail finisher, part of the exterior body trim running along the roof edge. Fitted above the door aperture, it c...

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Bolt with a 1/4" UNF (Unified Fine) thread. A threaded steel fastener used to secure body panels and ancillary fittings.

Brake Master Cylinder Repair Kit for reconditioning the dual-circuit brake master cylinder within the hydraulic braking system. The master cylinde...

First Gear Bush for the LT76 gearbox mainshaft. The bush journals the mainshaft first gear, providing the running surface on which the gear turns o...

Front Radius Arm Bush (rubber) located at the chassis end of the front radius arm. The bush is pressed into the radius arm mounting eye where the ...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

Front Coil Spring - Heavy Load, Standard Height (Terrafirma). These front coil springs are rated for heavy load while retaining the standard ride ...

Front Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

PAS pump assy Disco 2 TD5

Heater Blower Motor for the heater and ventilation assembly. Drives the blower fan that draws air across the heater matrix and distributes it throu...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Facia Panel Assembly - LHD is the end closing trim for the upper dashboard fascia on left-hand drive Defender 90 and 110, finished in black. This ...

Regulator Pressure Fuel 3.5V8 - EFI

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Brake Pipe Clip from the brake hydraulic pipe routing. It secures and locates a rigid brake pipe against the chassis or body, holding the run of t...

Wiper Blade - Front is part of the front windscreen wiper assembly. The blade clips onto the front wiper arm and sweeps across the windscreen to m...

Oil Pump Chain Kit for the Td5 2.5L 5-cylinder turbo diesel, part of the oil pump drive in the engine's lubrication system. The oil pump is driven...

Bolt - a hexagonal-head bolt with a 1/4" UNF (Unified Fine) imperial thread and a 1-1/4" length. Used as a body and chassis fixing at points such a...

Blind Rivet Pin is a plastic blind-rivet fastener, 9.4 mm head diameter by 13 mm long. It secures trim panels, covers and liners by expanding to g...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Step back into the golden age of Land Rover with this meticulously crafted 1:76 scale diecast model of the iconic Series 3 Hard Top in Bronze Green...

Intermediate shaft lock nut LT230

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Brake Pad Set - Rear - a set of friction pads for the rear disc brakes, forming part of the rear braking assembly. The pads locate in the rear bra...

Fuel Filter Assembly for the Td5 2.5L 5-cylinder turbo diesel fuel system. It filters the diesel supply between the tank and the injection system,...

Rear Exhaust Tail Pipe for the Land Rover Defender 90. This is the rearmost section of the exhaust system, connecting to the rear silencer outlet ...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Steering Column Top Support Seal for the steering column mounting, fitted at the top inner support bracket where the column meets the bulkhead. Th...

Leather hasp civilian

Safari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Non-Puma applications. The bolts secure the fixings of t...

Fuel Pump & Sender Unit - the in-tank fuel delivery module for petrol V8 EFI applications, combining the electric fuel pump and the fuel-level ...

Coolant Hose connecting the thermostat housing to the coolant pipe on the Td5 2.5L 5-cylinder turbo diesel engine. Part of the engine cooling circ...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

O-Ring seals the left-hand output of the Intermediate Reduction Drive (IRD) unit, part of the IRD casing and seal set. It sits at the joint where ...

Air Duct Seal - seals the heater air duct against the parcel tray within the HVAC air distribution. For vehicles without air conditioning.