Land Rover Parts

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Brake Master Cylinder is the primary hydraulic actuator of the braking circuit, converting pedal effort transmitted through the brake servo into th...

Upgrade your Land Rover Defender 90 & 110 (2002-2016) with this OEM-style Safari rear door, designed with pre-drilled spare wheel carrier holes...

Clevis Pin for securing the accelerator cable at the throttle pedal end. The pin connects the inner cable to the throttle pedal arm within the mec...

Alternator - A127-type 100A alternator serving the charging circuit of the 300 Tdi 2.5L turbo-diesel engine. Belt-driven from the crankshaft pulley...

Water Pump Gasket sealing the water pump to the engine in the cooling circuit. The 8-hole gasket matches the bolt pattern of the water pump mounti...

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Coolant Pipe routes coolant to the thermostat within the engine cooling circuit, forming a rigid section of the coolant path to the thermostat hous...

Rear Wheel Arch Kit, +30mm wide, supplied as a pair for the rear of the body. The arches extend coverage 30mm beyond the standard profile to suit ...

Front Wheel Arch Kit - extended +30mm width - for Defender 90 and 110, supplied as a pair. Moulded from plastic to closely match the profile of th...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Bolt - Water Pump is the 1/4" UNC x 2" fastener that secures the water pump to the Rover V8 engine, within the engine cooling circuit. It fixes th...

Slave cylinder

Brake Pad Set - Front for the front hydraulic disc brake assembly. The pads are clamped by the caliper against the brake disc to generate friction...

Front Swivel Pin Kit is a complete overhaul kit for the front axle swivel housings, the steering pivot assembly that allows the front hubs to turn ...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

LED Beanie Hat with a built-in 80-lumen LED lamp in the front panel, giving hands-free light in the direction the wearer is facing. The lamp runs ...

Aerial – Front Wing is the wing-top radio antenna for the vehicle audio system. The all-metal telescopic mast mounts to the top of the front wing ...

Front Brake Pad Set - XS for the front braking system, comprising the friction pads that seat in the front calipers. Under hydraulic pressure the ...

Fuel Connector Block for the Td5 2.5L 5-cylinder turbo diesel engine (Euro III, later specification). The block is the central junction of the fuel...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

107.5cm long 0.13cm thick

Air Suspension Strut - Front is a complete front corner unit for the air suspension system, combining the air spring and hydraulic damper into a si...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Clutch Control Valve is fitted in the hydraulic clutch release circuit between the master cylinder and the concentric slave cylinder. It regulates...

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Injector clamp bolt 2.4 Puma

Front Sill Panel for the left-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clos...

Fuel Tank Cradle from the rear fuel tank mounting - the steel support frame that carries the classic-pattern plastic fuel tank beneath the chassis....

Centre Handle Cover is the screw cover cap for the window winder handle, finished in black. This small cover conceals the retaining screw on the m...

Rear Fog Lamp Switch is the dashboard-mounted push-button control for the rear fog lamp circuit. This switch allows the driver to activate the rea...

Rear Fog Lamp Switch is the dashboard-mounted control for the rear fog lamp circuit. This switch allows the driver to activate the rear fog lamp f...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Brake Caliper Piston for the hydraulic disc brake caliper, 46mm diameter and 30.68mm height. The piston sits within the caliper bore and transfers...

Window Channel top run channel for the front door glass, fitted within the door frame aperture. The channel lines the upper edge of the window ope...

Past op 110 TD5 v.a. 1999 plastic tank achterin en Puma TDCI

Double DIN Console - one-piece centre console fascia in black, providing the mounting aperture for a double DIN head unit in the Td5 dashboard. It...

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

LED Light Upgrade Kit (deluxe smoked-lens type, 73mm) - a complete set of WIPAC LED lamps with smoked lenses, replacing the original incandescent f...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

Bulkhead Mounting Bolt - M12 x 180mm fastener securing the lower bulkhead to the chassis. Forms part of the body-to-chassis mounting at the base o...

Steering Guard - 8mm Alloy - LHD - Black for underbody protection of the steering linkage assembly. Constructed from 8mm laser-cut alloy plate wit...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...

Hub Bearing Spacer - 15.0mm - Black used in the front axle hub bearing assembly. This colour-coded spacer sits within the hub between the inner an...