Land Rover Parts

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Land Rover Grille Name Plate - Black & Silver - front grille name plate carrying the Land Rover lettering, finished in black and silver. Mount...

Clutch slave cylinder assembly

Timing Chain Guide for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The guide runs al...

Mud Flap for the left-hand side, covering both the front and rear wheel positions. Part of the exterior body protection. Fitted behind the wheel a...

Front Mudflap for the left-hand front wheel arch. Mounted behind the front wheel, it deflects road spray, mud, stones and debris thrown up by the ...

Mudflap – Rear – RH is the right-hand rear mudflap, fitted behind the rear wheel to reduce road spray and protect the bodywork from mud and stone t...

Radiator Grille - the front grille panel that fits in the front body aperture ahead of the radiator. It admits cooling airflow to the radiator whi...

Fuel Tank Vent Hose - part of the fuel tank ventilation circuit on Puma TDCi models. It carries fuel vapour from the tank, allowing the tank to br...

Thermostat Housing for the engine cooling system of the 3.6L TDV8 (Lion) V8 turbo diesel. It houses the coolant thermostat and provides the connect...

Intake Hose Range Rover Classic MA>, MA> - EFI Discovery 1

Rod LHD

This special nut (thread size M14) is used in the rear suspension system across several Land Rover and Range Rover models. It plays a crucial role ...

Exhaust Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 35mm head diameter and a single collet groove on the stem. It se...

Rear Air Spring Conversion Kit replaces the rear air suspension with conventional coil springs. It removes the self-levelling air springs from the...

Ensure the secure and hassle-free lowering and raising of your spare wheel with this spare wheel winch, designed for Land Rover models with an unde...

Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...

Door Filler is the sloping filler that closes the gap along the angled front edge of the front door. Part of the front door assembly, it seals the...

Sloping Panel Filler is the angled filler trim that closes the sloping section at the front of the front-door wind-up window aperture. This is the...

Window Regulator Motor - LH is the electric drive motor for the left-hand window regulator assembly. Mounted directly to the regulator mechanism, ...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Coolant Pipe forms a rigid section of the engine cooling circuit, carrying coolant between connection points on the cooling system. Fitted to the ...

Pipe assembly pump to steering box

Main Switch - heavy-duty main electrical switch rated at 1000A. Switches the primary high-current circuit, suited to continuous heavy-duty loads.

Decoke Gasket Set - 3.5L V8 - Carb

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Countersunk Screw is used to secure side door latch strikers on the Defender. The striker is the fixed plate in the door aperture that the door la...

Starter Motor - the engine cranking motor within the starting system, for the 2.25L and 2.5L 4-cylinder petrol engines. On ignition the solenoid t...

Overhaul Gasket Set - Bottom End covers the lower block of the 2.5L four-cylinder turbo diesel engine, supplying the gaskets and seals used when re...

Window Regulator Handle for the front door, operating the manual window regulator (winder mechanism) to raise and lower the door glass. The handle...

Steering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...

Upper Classic Speedo Cable - 90/110

Coolant Hose connecting the oil cooler to the radiator. Part of the engine cooling circuit, this hose carries coolant between the oil cooler and t...

Clevis Pin for the front door hinge and check strap assembly. This pin secures the door check strap (travel limiter) at its pivot, retaining the s...

Rear Exhaust Assembly - the rear section of the exhaust system, carrying the exhaust gases from the mid-section back to the tailpipe. Supplied as ...

Brake Pipe Clip - Double - a moulded plastic clip that secures two brake pipes to the chassis within the braking hydraulic circuit. It retains bot...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Exhaust Tailpipe forms the rearmost section of the exhaust system, carrying exhaust gas from the intermediate silencer to the rear of the vehicle a...

Fuel Tank with integral skid guard for the fuel storage system. The pressed-steel tank incorporates a welded underside skid guard that shields it ...

Fuel Tank Bracket for securing the fuel tank to the vehicle chassis. This metal bracket forms part of the fuel tank mounting assembly, locating an...

Rear Crossmember is the transverse structural section that closes and reinforces the rear of the chassis frame. Because mud, road salt and debris c...

Longitudinal Steering Tube for the Series III steering linkage assembly, applicable from axle number suffix E onwards. This tube connects the stee...

Rear door sill seal RH

Tailgate Seal for the rear end structure. This seal fits around the tailgate aperture, sealing the joint between the tailgate and the rear body to...

Heater Air Intake Valve - the flap valve assembly at the fresh-air inlet of the heater box. It opens and closes the intake to control the flow of o...

Bonnet stay stick Defender

Wheelarch Eyebrow is the front wheelarch eyebrow moulding, part of the front wheelarch trim assembly. It mounts to the upper section of the front ...