Land Rover Parts

Breather and oil filler cap for the rocker cover, part of the engine crankcase ventilation system on the 2.25L and 2.5L 4-cylinder petrol and natur...

Breather Hose connecting the camshaft cover to the inlet manifold, part of the engine's crankcase ventilation system. It routes crankcase blow-by ...

Differential Housing Gasket - Brass seals the joint between the differential housing and the axle casing, preventing oil leaks from the differentia...

Front Door Lock Set provides key-operated locking for the front doors and is of the anti-burst type, designed to resist the latch springing open un...

Piston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

4-Leaf Parabolic Rear Spring Pair for the rear suspension of Series long-wheelbase Land Rovers. Parabolic leaf springs use a progressive, variable...

Door Seal fits along the floor line of the rear side door aperture, sealing the gap between the lower edge of the door and the body sill. It block...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Oil Temperature Sensor is a transducer in the engine oil lubrication monitoring circuit, wired for 24V electrical systems. Threaded into the oil f...

Special bolt

External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Seat yoke

Sealing Plug for the transmission handbrake drum on the LT95 four-speed gearbox. The drum-type transmission handbrake acts on the transfer box out...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Radiator Hose forms part of the engine cooling circuit, connecting the radiator to the thermostat housing. It carries coolant between the radiator...

Crankshaft Woodruff Key for the 2.5L 300TDi and 2.5L Td5 diesel engines. This semicircular key seats in a slot machined into the crankshaft nose an...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Bolt 1/4" UNC x 1-1/4" is a coolant pump fixing bolt used on the 3.5L V8 petrol engine. It secures the coolant (water) pump to the engine within t...

Spring Retaining Plate Front coil spring retaining plate that clamps over the top of the spring at its seat, holding the spring captive so it canno...

Interior Trim Fastener - a grey drive-in fastener for securing interior trim panels in the cabin. It retains facia and carpet trim, the cubby box,...

Brake Master Cylinder Repair Kit for the Range Rover Classic hydraulic braking system. This rebuild kit contains the seals and components required...

Drive Belt for the coolant pump on the 3.5L V8 petrol engine, in the belt configuration used when air conditioning is fitted. The belt transfers d...

Windscreen Hinge Screw - the fixing that secures the windscreen frame hinge to the bulkhead, allowing the frame to be folded down on models fitted ...

Split Pin for the Range Rover Classic brake assembly. This split cotter pin, measuring 5/32" x 3" (approximately 4 mm x 75 mm), is used in the rea...

Distance Piece is the spacer fitted to the front halfshaft within the front axle and hub assembly. It sets the correct positioning of the halfshaf...

Carburettor Torsion Spring is the return spring fitted to the throttle linkage of the Zenith carburettor on the 2.25L four-cylinder petrol engine. ...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Banjo Bolt

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

H4 Halogen Bulb rated at 24V 70/75W (dip/main beam), for use in vehicle headlights on 24V electrical systems. Fits standard H4 (P43t cap) headlamp...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Rear Main Bearing Cap Seal for the Rover V8 petrol engine, sealing the joint between the rear main bearing cap and the cylinder block. This crucif...

Breather hose rocker cover

Brass Pipe Union - a male threaded connector used to join a 1/4" pipe into a fluid or pneumatic line. Machined from brass, it carries a male M12 x...

Hose Clamp is a worm-drive band clamp with a 70-92mm clamping range, used to secure a flexible hose onto a rigid spigot or fitting. Tightening the...

Sealing Washer is a copper crush washer used to seal banjo and threaded union joints in the fuel system. Fitted at unions such as the injection pu...

Hexagon Bolt - an M10 x 55 mm high-tensile bolt, property class 10.9, used to secure the rear stub axle and in the suspension top link, fulcrum and...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Cylinder Head for the Td5 2.5L 5-cylinder turbo diesel engine, later type. The cylinder head seals the top of the engine block, forming the combust...

Steering Box Output Oil Seal for the manual, non-power-assisted steering box. It seals the output (rocker) shaft where it exits the steering box h...