Land Rover Parts

Thermostat housing replacement

Heater Hose - Outlet is a moulded coolant hose within the heater circuit of the HVAC system. It carries coolant away from the heater matrix outlet...

Radiator Top Hose for the engine cooling system. This upper hose carries hot coolant from the engine's thermostat outlet to the radiator top inlet...

Engine Oil Cooler for the diesel engine oil cooling circuit. This oil cooler assembly manages engine oil temperature by transferring heat between ...

Top Coolant Hose - the upper radiator hose in the engine cooling circuit. It carries hot coolant from the engine outlet to the top of the radiator...

Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...

Exhaust Downpipe - LH - V8 is the left-hand front section of the exhaust system on V8 petrol applications. It connects the left-hand exhaust manif...

Body Side Seal is the left-hand upper rear body side seal, part of the rear body sealing assembly. It runs along the upper edge of the rear body s...

Side Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...

Mudflap Bracket – LH is the left-hand mounting bracket for the mudflap. It secures the mudflap to the body behind the wheel, holding it in positio...

Suspension Arm - rear lower control arm for the right-hand side. It forms part of the rear suspension, connecting the chassis to the wheel hub carr...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Front Hub Assembly, left-hand side, for the front axle. It carries the front wheel bearing and provides the mounting flange for the road wheel and ...

Radiator & Intercooler Assembly - the front-mounted engine cooling unit for the 300 TDi 2.5L 4-cylinder turbo diesel, combining the coolant rad...

Airflow sensor 4L V-8 engines

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Cellular Dynamic Shock Absorber A long-travel rear damper that controls axle movement within the suspension, mounted between the chassis and the re...

Number Plate Mounting bracket for securing a front number plate, measuring 405mm wide by 110mm deep. The bracket provides a flat mounting face for ...

Seat Back Foam is the moulded cushioning for the outer front seat back. It forms the padded profile that sits over the seat back frame, beneath the...

Swing-Away Spare Wheel Carrier mounts the spare wheel on a pivoting arm at the rear of the vehicle, for the half-door tailgate configuration. Carr...

Castor Correction Wedge, supplied as a pair, for leaf-sprung suspension. The wedges fit between the leaf spring and the axle to reset the axle pini...

Floor Mat is a moulded rubber footwell mat shaped to fit the left-hand floor over the gearbox tunnel. The foam backing adds sound insulation under...

Rear End Door Hinge - Upper for the rear end door (tailgate) assembly on Land Rover Discovery 1 and Discovery 2. This upper hinge mounts at the to...

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

Rear Trailing Arm Bush for the rear suspension, mounting the radius (trailing) arm to the chassis. The bush locates the arm while allowing the cont...

Seatbase Storage Lid closes the storage locker built into the seat base. This lid fits over the stowage compartment within the seat base, providin...

Window Regulator for the front door, left-hand side. The regulator is the mechanism inside the door that raises and lowers the door glass, carrying...

Power Steering Pump Seal Kit – Cast provides the seals needed to overhaul the cast-bodied power steering pump within the steering hydraulic circuit...

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Wheel Nut - retaining nut for the rear door-mounted spare wheel. This nut secures the spare wheel to its carrier on the rear door. Its seat is pro...

Designed for use with heavy-duty steering arms, this kit provides the necessary brackets and hardware for a solid fitment, enhancing steering stabi...

Door Top Glazing Kit supplies the fixings and retaining components used to secure the glass within a door top frame. Fitted when glazing or re-gla...

Demister Outlet Finisher - vent finisher set into the top of the dashboard over the windscreen demister outlet, directing heated and ventilated air...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Bonnet Release Cable connects the in-cabin release lever to the bonnet catch. Part of the bonnet locking mechanism, it transmits the pull of the r...

Inner waist seal 90/110/130 classic Defender

Front Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...

Idler Pulley - timing belt idler for the 200 TDi and 300 TDi engine. Provides a bearing surface on the timing belt path, guiding the toothed belt ...

Floor Mat is a moulded rubber footwell mat shaped to fit the right-hand floor over the gearbox tunnel. The foam backing adds sound insulation unde...

Cap - Pressure - Radiator

Heavy Duty spring Range Rover rear +0mm

Aluminium Pop Rivet, a blind rivet used as a general fixing for body panels, interior trim and seat-mounting brackets. It is set with a rivet gun: ...

Battery Cover - the protective cover fitted over the battery in the engine bay. It shields the battery casing and terminals from debris and accide...

Sump Gasket for the 2.0L MPI T-Series 4-cylinder 16-valve petrol engine, sealing the oil sump to the underside of the cylinder block. It forms the...

Gearbox Heat Shield fitted to the transmission mounting assembly, protecting the surrounding components from exhaust and drivetrain heat. By reduc...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...