Land Rover Parts

Intercooler Hose Kit - Silicone Black for the turbocharger and intercooler air circuit on the TD5 2.5L 5-cylinder turbo diesel engine in the Defend...

Fuel tank filler hose pipe

Battery Cover is the top fixing frame of the battery securing assembly. It clamps down over the top of the battery and bolts to the battery tray, h...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Clutch Slave Cylinder Push Rod for V8 applications, part of the hydraulic clutch release circuit. The push rod transfers movement from the slave c...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Water-in-Fuel Sensor for the Td5 2.5L 5-cylinder turbo diesel fuel filter / sedimentor assembly. It threads into the base of the fuel filter housi...

Fuel Filter Holder - With Filter for the Defender Puma diesel fuel system. This complete filter assembly mounts in the engine bay fuel circuit and...

Starlock Washer - a push-on retaining washer used to secure components onto plain shafts and rods without the need for threading or tools. Once pr...

Cylinder Head Bolt Set for the 1.8L K-Series 4-cylinder petrol engine. The set secures the cylinder head to the block, clamping the head gasket to ...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Spacer 15,1mm Green

Spring Retaining Plate - Rear for the rear coil spring seating assembly on Defender 110 and 130. Coil springs can become dislodged from their axle...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Front Drive Shaft - Right-Hand, supplied complete with constant velocity (CV) joint. This halfshaft transmits drive from the front differential to...

Hex Head Bolt, M10 x 30 mm. A metric hex head bolt with a 10 mm thread diameter and 30 mm shank length, used as a general fixing across a range of...

Rear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...

Rocker Cover Gasket Set for the 2.5L VM turbo diesel engine, sealing the rocker cover to the cylinder head. The gasket seats between the rocker co...

Rear Brake Caliper Seal Kit for rebuilding both rear brake calipers on the Discovery 2 and Range Rover P38, supplied as a pair to cover both sides ...

Headlamp Gasket for the headlamp mounting assembly. A rubber seal that fits between the headlamp unit and the surrounding body panel, providing a ...

Warning Bulb Switch (Red) for the facia auxiliary switch panel. Mounted in the upper facia switch bank, this illuminated switch carries an integra...

Rear Hub Wheel Bearing for the rear hub assembly. It supports the rear wheel hub on the stub axle, allowing the wheel to rotate freely while carryi...

Intercooler Hose - a charge-air hose in the turbocharged diesel induction system. It forms part of the boost circuit that carries pressurised air ...

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

A-Post Finisher is the trim cover for the right-hand A-post, the windscreen pillar, concealing the pillar structure and dressing the join between t...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Tailgate Gas Strut - Upper for the rear split tailgate, supporting the upper lift-up section of the door. The gas-charged strut counterbalances th...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Fuel Return Hose forms part of the fuel return line on the 2.2L Puma TDCi diesel engine. It carries surplus fuel from the injection system back to...

Body Strap - 2 Hole is a foam mounting spacer used in the front windscreen hinge assembly on the Defender. This two-hole component sits between th...

Crankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...

Drive Shaft Oil Seal for the front and rear hub assemblies. This lip seal fits at the inboard end of the front and rear hub carriers, sealing axle...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Radiator Hose is the bottom (lower) coolant hose in the engine cooling system, connecting the radiator outlet to the water pump inlet. It carries ...

Inlet Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 44.5mm head diameter. It seats in the inlet port of the combustion...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Self-Tapping Screw - a No. 8 general-purpose self-tapping fastener used at body and interior trim fixing points. The screw cuts its own thread as ...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Bolt - M16 x 90mm is a hexagon head bolt used in the front suspension assembly of Land Rover vehicles. Fits the radius arm mounting, securing the ...

Power Steering Hose forms the low-pressure feed line of the power steering hydraulic circuit, carrying fluid from the reservoir to the inlet of the...

Rear Bumper Lamp Assembly - right-hand rear lamp unit mounted in the rear bumper, forming the lower section of the rear lighting cluster on the rig...

Gearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...