Land Rover Parts

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Engine Overhaul Gasket Set for the 2.6 litre IOE (inlet-over-exhaust) 6-cylinder petrol engine. A set of the gaskets and seals used when stripping...

Front Brake Caliper for the front hydraulic braking circuit, mounting over the brake disc on the right-hand side of the front axle. Internal pisto...

Main Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...

Battery Clamp - the hold-down that secures the battery in its tray. It bears down on the battery to stop it shifting under vibration and off-road m...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Alternator - 150A Water-Cooled - the charging unit for the vehicle's electrical system, mounted to the front of the engine and driven by the access...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Flat plain washer used within general fastening applications across multiple vehicle assemblies, providing a load distribution surface between the ...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

Trunnion

Fuel Pipe Sealing Washer seals the fuel pipe union at the DPA diesel injection pump. Fitted at the union connection, it is compressed between the ...

Wheel Hub Assembly - the complete axle hub, supplied with the wheel studs already fitted. It serves both front and rear hub positions. The hub mou...

Tow Electrics Wiring Harness - N Type Socket - plug-in wiring harness providing an N-type 7-pin socket at the towbar, enabling connection of traile...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Door Glass Regulator Shim - a packing shim used at the door window regulator and glass channel. It sets the regulator and channel at the correct st...

Fuel Filler Hose connecting the external fuel filler neck to the fuel tank on the Defender. This rubber hose forms the sealed connection between t...

Front Differential Oil Seal - a rotary shaft seal fitted to the front differential to retain gear oil and exclude dirt and water where the drive sh...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Roof Access Ladder Rear Assembly is a rear-mounted access ladder with an integrated rear lamp guard. It mounts to the rear bodywork to provide saf...

Make traveling with kids fun and hassle-free with the Range Rover Sport SVR Convertible Ride-On Suitcase. This officially licensed suitcase replica...

Rear Coil Spring for the rear suspension, fitting between the axle and the chassis spring seat to support the vehicle and absorb road inputs. This...

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Sunroof Seal for the manual sliding sunroof. The rubber seal fits around the sunroof aperture and seals the panel against the roof to keep out wate...

Fits Defender 110 (1999 onwards) with 2.5 Td5 Diesel, 2.2, and 2.4 Puma Diesel engines Non-galvanised for a strong, reliable solution 16cm ext...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Connector inline female imperial 3/8 X 24 UNF x2

Fitment: - Classic Defender: TD5 diesel models - Discovery 2: All TD5 diesel models and All V8 EFi petrol models - Range Rover P38: 2.5L 6 Cyl B...

Output Shaft - MT82 6-Speed Manual Gearbox. The output shaft is located at the rear of the MT82 transmission housing and transmits rotational driv...

Clutch Hose within the hydraulic clutch circuit of the Puma TDCi Defender. The hose carries hydraulic fluid between the clutch master cylinder and...

Piston Ring Set Standard. 2.25 / 2.5 Diesel (Per Piston)

Water Pump for the engine cooling circuit of the 2.5L 4-cylinder naturally aspirated diesel, petrol and pre-TDi turbo diesel engines. Belt-driven f...

In-Tank Fuel Pump & Sender Unit for Range Rover P38A petrol applications. This combined assembly houses the electric fuel pump and fuel level s...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Bottom Gasket Set for the 3.9L V8 EFI petrol engine, covering the lower (bottom-end) section of the engine during an overhaul. The set provides th...

Front Brake Caliper for the right-hand side. The caliper straddles the front brake disc and houses the hydraulic pistons that force the brake pads ...

Air suspension compressor c/w drum

Thermostat regulates coolant flow within the engine cooling circuit. It stays closed while the engine is cold to speed warm-up, then opens at its r...

Rear Fog Lamp - LED, 95mm round, clear lens, for North American Specification (NAS) Defenders. The lamp fits the standard 95mm round rear fog lamp...

Door Pillar Repair Bracket for the front right-hand (offside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

Bulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...

Exhaust manifold gasket Puma

Rear Crossmember is the transverse structural member that closes the rear of the Defender ladder chassis, tying the two chassis rails together and ...

Vacuum Pump Seal - 2.7 TDV6 is the sealing component for the engine-driven vacuum pump on the 2.7L TDV6 diesel. The vacuum pump is mounted on the ...