Land Rover Parts

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Front Brake Pad Set for the front braking system, comprising the friction pads that seat in the front calipers. Under hydraulic pressure the calip...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Column Stalk Switch mounted on the steering column, combining three controls in a single stalk: the turn-signal (indicator) switch, the horn push a...

Diesel Fuel Filter - Inline for the 2.5L TDi and Td5 2.5L 5-Cylinder diesel fuel system. Fitted at the sedimentor position in the fuel supply line...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Glow Plug Conversion Kit for the 2.25L diesel engine, replacing the original series-wired heater plugs with parallel-wired glow plugs. In the origi...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Pipe clutch down

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Oil seal

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Brake Master Cylinder is the hydraulic control unit of the braking system, generating the fluid pressure that actuates the wheel cylinders at each ...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Front Brake Caliper for the front hydraulic braking circuit, mounting over the brake disc on the left-hand side of the front axle. Internal piston...

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Door Lock Striker for the door locking system. This component mounts to the body aperture pillar and provides the fixed engagement point for the d...

Headlamp Finisher for the front wing panel, fitted on the right-hand side as the outer surround that frames the headlamp aperture. The finisher lo...

Courtesy Light Switch is a door-actuated contact switch in the interior lighting circuit, mounted at the door pillar aperture. When the door is op...

Oil Filter Housing Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the oil filter housing/adaptor to the cylinder block. It sea...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Stub Axle Oil Seal - Inner

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Pinion Oil Seal sealing the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Grommet

Brake Pipe Union - a male union fitting for 3/16" (4.75mm) hydraulic brake pipe, with a 7/16"-20 UNF thread. It clamps the flared pipe end against...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Windscreen Wiper Wheelbox Spindle Housing for the windscreen wiper rack mechanism. The unit mounts through the bulkhead or scuttle panel and suppo...

Instrument Bulb - 12V 2.2W for the instrument panel. Replacement dial illumination bulb for the speedometer on Range Rover Classic Police Vehicle ...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Bulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...

Air Bleed Valve for the fuel filter and sedimenter housing, part of the diesel fuel supply system. Mounted in the filter housing, the valve allows...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Tailgate Aperture Seal for the rear body aperture sealing assembly. Fitted around the perimeter of the tailgate body opening, this seal forms the ...

Rear Axle Half Shaft for the left-hand side, part of the rear axle Hubs & Driveshafts assembly. Transmits drive torque from the rear different...

Clip is a multi-purpose retaining clip used to secure cables, harnesses and small components in their mountings. It locates and holds items such a...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Thermostat regulates coolant flow within the engine cooling system, with an opening temperature of 82°C. It remains closed while the engine is col...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Gear Lever Gaiter - rubber gaiter fitting over the gear lever and transfer box lever at the transmission tunnel diaphragm panel, sealing the tunnel...

Shackle Pin - Long (9/16 UNF × 5-1/4 in.) for the front leaf spring shackle on Land Rover Series vehicles. This long shackle pin is fitted at the ...