Land Rover Parts

Self-Tapping Screw - a No. 8 x 1/2" self-tapping screw used as a body-trim fixing. It secures body trim panel brackets, headlamp finisher panels a...

Drive Screw - a No. 6 x 5/8" self-tapping drive screw used as a body fixing. It retains the grille assembly and secures the rear door and tailgate...

Rubber Buffer for the door-top sliding side window. The buffer fits at the top of the door and acts as an end-stop for the sliding glass, limiting...

Electronic Conversion Kit - electronic ignition conversion for the 4-cylinder petrol points distributor. Replaces the contact breaker points and c...

Rear Door Hinge Bolt - Lower - Torx 95mm is a 95 mm Torx-head bolt used at the lower fixing point of the rear side door hinge and check strap. It ...

Accelerator Cable - throttle cable for TDi diesel applications. It connects the accelerator pedal to the injection pump throttle lever, transmitti...

Tappet kit

Exhaust Clamp sized for 60mm nominal pipe, part of the exhaust system hardware. It secures a slip-fit joint between two adjacent exhaust sections,...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Belt Drive 2.4tdci Non-a/C 2621mm

Radiator Assembly for the Range Rover P38 cooling system, fitted to the 2.5L Diesel engine. The radiator dissipates heat from engine coolant circu...

Exhaust Downpipe (Y-Pipe) - the front section of the exhaust system that bolts to the exhaust manifolds. The Y-pipe collects the exhaust flow from...

Dump Valve

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Exhaust silencer rear 90 from vin MA939976 to vin TA999221

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Window regulator front RH

Hot Plug is the pre-combustion chamber insert, or hot spot, seated in the cylinder head of the 2.5L 4-cylinder naturally aspirated and 2.5L 4-cylin...

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Front Cover Gasket for the 2.5L 200TDi diesel engine, the smaller of the front cover gaskets. It seals the joint between the front cover and the c...

Polyvee Belt 3.9V8 1253mm

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Oil Seal - Clutch Housing for the manual transmission drivetrain on the Freelander 1. This oil seal is located at the clutch housing and prevents ...

Bolt Threaded fastener used within the exhaust system assembly.

Bump Stop - rubber suspension bump stop for the Range Rover P38, fitted to limit suspension travel at full compression and absorb the final impact ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Oil Temperature Sender for the engine oil temperature gauge circuit. The sender threads into the oil gallery and carries a temperature-sensitive re...

Coolant Hose connects the heater circuit to the thermostat housing, routing coolant between the heater matrix feed and the thermostat within the co...

Coolant Hose carries coolant through the engine bypass circuit, connecting the bypass outlet to the thermostat housing. It is the upper hose in th...

Wiper Blade for the front windscreen wash/wipe system, for left-hand drive applications. Fits the wiper arm clip and sweeps the windscreen in LHD ...

Upgrade your Land Rover Freelander 2 (2.2 TD4 Diesel) with this high-performance Silicone Turbo Hose Kit, designed to handle higher temperatures an...

Piston

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Flange rear

Distributor Cap for the 2.6L 6-cylinder petrol ignition system on the Land Rover Series III. Fitted over the distributor body, the cap receives hi...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Green Bulb for the facia and auxiliary switch panel. This small bulb provides the green illumination behind the dashboard auxiliary switches and u...

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Fuel Tank Sender Unit for the petrol fuel level sensing circuit. The sender uses a float arm connected to a variable resistor to measure the fuel ...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Piston Ring Set for the 2.25L and 2.5L naturally aspirated diesel engine, supplying the ring pack for one piston. The rings seat in the piston rin...

Lower Steering Shaft Universal Joint for the steering column assembly, forming the lower coupling between the steering column and the steering box ...

Hose Clamp with a 10-16 mm clamping range. Used to secure rubber hoses at cooling, fuel, and fluid circuit connections on Land Rover vehicles.