Land Rover Parts

Lower Steering Drop Arm for the steering relay assembly. This is the lower lever that clamps to the bottom of the steering relay shaft. Within the...

Washer for the windscreen and handbrake assembly on Series 2, Series 3, and Military Land Rover vehicles.

Front Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...

Front Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...

Brake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...

Grommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...

Front Mudflap Kit for the body and chassis, supplied as a matched left- and right-hand pair. Fitted behind the front wheels, the flaps deflect roa...

Mudflap Bracket – RH is the right-hand mounting bracket for the mudflap. It secures the mudflap to the body behind the wheel, holding it in positi...

Injector Pipe - No.3 for 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. This high-pressure steel fuel pipe routes fuel from the me...

Alternator Drive Belt for the Discovery 2 fitted with the V8 Petrol engine, air conditioning, and no ACE (Active Cornering Enhancement) system. Th...

Front Grille - Horizontal for Range Rover Classic. This is the horizontal-slat style front radiator grille introduced with the 1987 facelift and u...

Rear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...

Seat Squab Hinge Link Rod - LH is part of the rear forward-facing split seat squab hinge assembly. The link rod connects the seat squab (backrest)...

Engine Mounting for the V8 petrol engine, forming part of the powertrain support system. It locates between the engine bracket and the chassis, ca...

Stub axle

Fuel Filler Neck Seal for the fuel filler assembly on the Defender. This rubber seal fits at the joint of the fuel filler neck, sealing the connec...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Air Suspension Compressor Seal Kit reseals the piston assembly of the Dunlop electronic air suspension (EAS) compressor, restoring the seal between...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...

Fuse - 100A high-current rated fuse for the main electrical protection circuit. Rated at 100 amps, this fuse protects the highest-current circuits...

Cigar Lighter Mounting Plate, the fascia panel that carries the cigar lighter unit. It mounts into the dashboard fascia, locating and retaining th...

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

Fuel Filter for the diesel fuel supply system — the cartridge that cleans fuel on its way to the injection pump. The filter traps particulate cont...

Banjo bolt

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Steering Column Switch

Brake Pipe Clip is a retaining clip from the front brake line mounting hardware. The treble form holds three rigid brake pipes side by side at a f...

Bonnet Frame Top Hat Supports are top-hat section reinforcement pieces that weld to the underside of the bonnet frame, stiffening the outer bonnet ...

Front wheel bearing kit for the hub assembly without ABS. This kit provides the bearing components required to support the front wheel hub, allow...

Choke Cable for the DA2126 Weber carburettor conversion. This cable links the dashboard choke control to the carburettor's choke mechanism, provid...

Cubby Box Black Mesh - Series 3 - Defender

Throttle Potentiometer Kit adapts the Rover V8 plenum chamber to accept a Colvern throttle position sensor in place of the original two-bolt potent...

Fir Tree Fastener is a push-fit trim clip that retains roof insulation against the vehicle body. Its ribbed fir-tree shank pushes into a pre-forme...

Coloured Lamp Kit is a complete set of 73mm round lamps for the front and rear lighting positions, supplied with coloured lenses. The kit contains...

Body Stay - Lower - Rear - RH Right-hand lower stay forming part of the rear body mounting. It locates the lower rear corner of the body to the ch...

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

AUTOGEAR POWER SYN 75W-90 is based on high quality synthetic base oil in combination with a special additive package to ensure the following proper...

Carburettor Float Assembly for the Zenith carburettor used on 2.25L and 2.5L 4-cylinder petrol engines. The float sits in the carburettor float ch...

Carburettor Float for the Zenith 361V carburettor, part of the Fuel System assembly on Series petrol engines. The float rides on the fuel surface ...

Water Pump Gasket for the 2.4L and 2.5L VM diesel engine, sealing the interface between the water pump housing and the engine block. This gasket i...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

Wiper Switch Assembly

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Adjustable Tow Bar Kit with quick-disconnect coupling for the rear towing system. The height-adjustable drop plate lets the tow ball height be set...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...