Land Rover Parts

Wiper Arm - front windscreen wiper arm, left-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spindl...

Headlamp Finisher for the front wing panel, fitted on the left-hand side as the outer surround that frames the headlamp aperture. The finisher loc...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Interior Lamp Lens for the centre interior lamp mounted in the headlining. The lens is the translucent cover that locates over the centre courtesy...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Master Cylinder to Pedal Box Gasket for the hydraulic clutch circuit. This gasket seals the mounting face between the clutch master cylinder body ...

Shackle Pin (9/16 UNF × 4-1/2 in.) for the leaf spring suspension on Land Rover Series vehicles. This medium-length pin is used at the forward (ch...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Swivel Pin Lock Tab for the front swivel pin housing on Land Rover Series II, IIA, and III. Fitted to the 7/16 BSF studs that retain the swivel pi...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Rear Propshaft for the driveline, transmitting rotational drive from the transfer case output to the rear axle input. Supplied as a complete balan...

Windscreen Wiper Motor for the front wiper system, supplied as a motor assembly with the integral reduction gear, park switch and drive cable. The...

EGR Blanking Kit for the Td5 2.5L diesel, used to remove the exhaust gas recirculation (EGR) valve from the inlet manifold and seal off the EGR fee...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Hub Bearing – inner taper roller bearing for the front and rear wheel hubs. The bearing sits inside the hub and runs on the stub axle, carrying th...

Fuel Filler Breather Hose

Lock Button for the door locking mechanism on Defender and Range Rover Classic. This black interior door lock button connects to the door latch ro...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Front Seat Belt Assembly - Long End - left-hand inertia reel seat belt assembly forming the active (retractor) end of the front occupant restraint ...

Diesel Fuel Filter - Inline for the 2.5L TDi and Td5 2.5L 5-Cylinder diesel fuel system. Fitted at the sedimentor position in the fuel supply line...

Gasket thermostat by-pass Series 2.25 petrol and diesel.

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Ensure smooth and precise steering in your Series 2, 2A, and 3 with this comprehensive steering box repair kit. Designed to replace worn components...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Power steering seal kit

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

See fitting instructions: https://www.scribd.com/doc/208898844/Fitting-Instructions-for-RTC3176-Adjuster-Shoes-Drum-brake-LAnd-Rover-Series

Stub Axle Locking Plate - Mudshield

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Brake Hose - the flexible hydraulic line in the braking system. It carries pressurised brake fluid from the rigid chassis-mounted brake pipe to the...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Water Pump Gasket - 9-Hole for the cooling system on Land Rover Series 2.25L Petrol engines. This gasket seals the mating face between the water p...

Rear Side Window Seal for the fixed rear side window assembly. This rubber glazing seal is designed for 4mm glass and installs between the body ape...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Front direction indicator lamp for the vehicle lighting system. This unit provides the flashing directional signal function at the front of the v...

Oil Seal installed within the wheel hub assembly to retain lubricant and prevent contamination ingress at the hub-to-stub-axle interface. The seal...

Exhaust Rubber Mounting suspends the exhaust system from the chassis, supporting the silencer and pipework at its mounting points. The rubber elem...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Oil filler cap

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...