Land Rover Parts

Spindle rod link

Compressor assy 9A (compressor only)

Luggage Tie-Down Hook - anchor hook in the luggage compartment for securing loads, integrated with the side trim retainer. Located in the luggage ...

Front Suspension Bolt, an M14 x 103 mm flanged-head bolt securing the front lower suspension control arm at its inner mounting to the subframe. Th...

Bonnet Release Cable for the Discovery 2 bonnet release system. This cable connects the interior bonnet release handle (located in the driver's fo...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Wiper Blade LHD and RHD

Glass mirror D1, D2 RH

Reverse switch R380 Frl.1 manual

Drip Rail Clip - Side Finisher for the Discovery 1 roof drip rail assembly. This clip retains the side drip rail finisher strip along the roofline...

Fitment: All Models Except TD5

Special Bolt for the front suspension radius arm. This M16 bolt secures the radius arm at its mounting, locating the arm against the chassis and a...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Drop Arm Nut for the Gemmer 6-bolt steering box on the Defender 90/110 and Range Rover Classic. This hex nut secures the steering drop arm to the ...

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Trunnion

Front Stub Shaft forming part of the front axle assembly on the Series 3 Long Wheelbase (109"). The stub shaft sits within the swivel housing and ...

Starter Pinion Retaining Kit for the inertia (Bendix) drive of the starter motor fitted to 4-cylinder and 6-cylinder petrol engines. The starter p...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Drive Belt for the air conditioning compressor, part of the accessory belt drive on the 3.5L V8 petrol engine. The belt transfers drive from the c...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Washer

O-Ring for the Zenith carburettor, part of the Fuel System assembly on the 2.25L 4-cylinder petrol engine. This O-ring provides a fluid-tight seal...

Power Steering Filter for the power-assisted steering (PAS) fluid reservoir, part of the Steering Hydraulic Circuit. This filter element sits insi...

Propshaft Yoke for the propshaft flange joint, part of the Drivetrain assembly. This flange yoke bolts to the transfer case or axle flange and acc...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Stop/Tail Lens is the replaceable coloured lens for the rear stop and tail lamp assembly. It fits over the large 3 inch (76 mm) round lamp body, s...

Upper Brake Pipe for right-hand-drive applications, part of the braking hydraulic circuit. This rigid metal pipe carries pressurised hydraulic flu...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Handbrake Shaft Washer locates on the handbrake relay shaft within the transmission handbrake linkage. It forms part of the handbrake relay lever ...

Clutch push rod

Mainshaft - Series 3

Layshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...

Lock Stop Bolt, Front Axle sets the steering lock stop on the front axle. Its head contacts the stop face on the axle to limit swivel travel, cappi...

Oil Filter Gearbox

Fuel Tank for the 3.5L V8 petrol engine. This is the main fuel storage tank, the reservoir of the vehicle's fuel supply system. Mounted to the cha...

Bottom link mounting RRC polyurethane pair

Mounting Link Bottom Range Rover Classic

Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...

Ball Steel Bearing

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Gear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Window Catch Mask fits behind the window catch on the rear side door. This plate seats between the catch and the door skin, masking and reinforcin...

Decal – Dash is an adhesive instrument switch-tab label for the dashboard control panel. It is applied to the face of a plastic switch tab to iden...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...