Land Rover Parts

Flanged Nut is a hexagonal nut with an integrated flange at its base. The flange spreads clamping load across a wider bearing surface, removing the...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Timing Belt Tensioner for the 2.5L Td5 5-Cylinder Turbo Diesel engine timing system. The tensioner pulley bears directly against the timing belt a...

Track Rod Tube Assembly forms the transverse steering link within the front steering linkage, tying the two front swivel steering arms together so ...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Sliding Window Catch for the front door sliding window assembly on Series Land Rover models. This black plastic catch secures the sliding window p...

Fuel Filter Non-Return Valve Kit for the Td5 fuel filter housing, in the low-pressure fuel supply circuit. The non-return valve maintains fuel pri...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Fuel Tank Top Gasket sealing the sender, pump or pick-up unit against the top face of the fuel tank. A flat sealing gasket fitted at the tank-top ...

Front Bumper for the front-end body structure, finished in black. The bumper mounts across the front of the chassis to form the front impact face ...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Small upper hinge windscreen gasket

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Camshaft Oil Seal for the rear of the Td5 2.5L 5-Cylinder diesel engine. Fitted at the rear of the cylinder head camshaft bore, this seal prevents...

Brake Pipe - Wheel Cylinder is a rigid hydraulic brake pipe in the front brake circuit, running from the brake backplate to the flexible jump hose....

Door Hinge for the rear end (load/tail) door, lower position. One of the pair of side-hinged door hinges that mount the rear door to the body aper...

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Rubber Mat Set for the front footwells - a pair of moulded rubber floor mats covering the driver and passenger sides of the cab floor. The mats ar...

Inlet Manifold Gasket for the Td5 2.5L five-cylinder diesel, sealing the inlet manifold to the cylinder head. The gasket forms the air-tight joint...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Door Lock Barrel Set for the body locking system, supplying replacement lock cylinders for the door and body locking points. The barrels integrate...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Front Bumper End Cap - Outer, installed at the outer section of the front bumper assembly. This component forms part of the Front Bumper & Bum...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Door Top Seal Strip for the front door assembly. This rubber seal runs along the upper section of the door frame, sealing the gap between the door ...

Front direction indicator lamp for the vehicle lighting system. This unit provides the flashing directional signal function at the front of the v...

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Manifold Gasket - inlet to exhaust manifold gasket for the 2.25L 4-cylinder petrol engine. On this engine, the inlet and exhaust manifolds bolt to...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Inside Door Handle Bezel The interior trim escutcheon that surrounds the door release handle on the inner door panel, finishing the opening around ...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Glass Run Channel for the door window aperture, supplied in a 2 m length. The channel lines the door frame to guide and seat the side window glass...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...