Land Rover Parts

Wheel Hub Assembly for the front or rear axle, supplied complete with wheel studs. The hub carries the road wheel and rotates on the axle taper be...

Swivel Pin Lower Bracket is a retention bracket in the front axle swivel pin housing assembly. Installed at the base of the swivel pin housing, th...

Turbocharger Outlet Gasket for the 2.5L Turbo Diesel and 200TDi engines, sealing the flanged joint between the turbocharger and the exhaust elbow a...

Manifold to turbo gasket 200TDi

Engine Cooling Fan - 11-blade, 17-inch diameter mechanical fan for the engine cooling system. Driven from the front of the engine via a viscous co...

Front Silencer for the Defender 110 200Tdi exhaust system, covering vehicles produced from 1990 to 1994. This silencer fits in the front section o...

Centre Exhaust Silencer Pipe - the intermediate section of the exhaust system on the 200 TDi 2.5L 4-cylinder turbo diesel, running between the fron...

Tail Pipe is the rear section of the exhaust system, carrying exhaust gas from the silencer to the outlet at the rear of the vehicle. This is the n...

Cylinder Head Gasket for the 2.5L 200/300 TDi turbo diesel engine, sealing the joint between the cylinder head and the engine block. It seals the ...

Camshaft for the 3.9L V8 EFI petrol engine. Mounted within the cylinder block of this overhead-valve, cam-in-block engine, the camshaft is driven ...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Front Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Seat Re-trim Kit (Inner) re-covers the front centre seat, renewing the cushion and squab foams together with their outer covers to restore the seat...

Clutch Kit renews the friction components of the Td5 driveline clutch and is supplied without the release bearing. The kit comprises the clutch co...

Centre Silencer Replacement Pipe occupies the centre section of the exhaust system, replacing the original centre silencer with a free-flowing stra...

Footwell Repair Panel is a welded body repair panel for the right-hand (nearside) footwell, replacing the corroded or damaged footwell section ahea...

Maintain a warm and comfortable cabin in your Land Rover Series 3 with this high-quality heater matrix radiator. Designed as a direct replacement, ...

Front Chassis Leg for the left-hand (nearside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...

Castor Correction Wedges - a pair of tapered wedges fitted between the front axle and the leaf springs to restore the castor and differential pin a...

Glazing rubber

Screw - Bonnet Hinge - M6 x 20 for the bonnet hinge assembly on the Defender. This M6 x 20 Torx-head screw secures the bonnet hinge. Used on vehic...

Seat Belt - Rear Centre Lap - Long End for the rear seat belt assembly in the Defender passenger compartment. This is the long webbing end of the ...

Fitment: All Models 2.7 TDV6 To (V) 6A999999 2.7L TDV6 diesel models to (VIN) 6A999999

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

ACE Hose is the suction hose within the Active Cornering Enhancement (ACE) hydraulic circuit. It carries fluid from the ACE reservoir to the inlet...

Bolt is a 3/8" UNF threaded fastener used in body and chassis structural assembly, securing frame and rear-end structure components.

Drag Link Tube is the central tube of the steering drag link, for left-hand-drive applications. It carries the track rod ends that connect the ste...

Brake Hose - Front - RH Flexible front brake hose in the hydraulic braking circuit. It carries brake fluid from the chassis-mounted rigid brake pi...

Washer Pump draws fluid from the washer reservoir and delivers it to the windscreen jets. Mounted in the base of the washer bottle, this pump serv...

Front door latch link

Rear Window Catch Assembly, right-hand, for the side-opening rear window in the rear body. This catch latches the hinged rear side window to its f...

U-Bolt secures a leaf spring to its axle in the suspension. The U-shaped bolt passes around the axle tube and clamps down over the spring pack thr...

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Injector Bolt - the banjo bolt at the injector spill-return (leak-off) union. It clamps the leak-off pipe fitting to the top of the injector, its ...

Spire Nut is a spring-steel push-on clip fastener that provides a threaded anchor in thin sheet metal. The nut pushes over a hole in a panel and r...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Rear left-hand leaf spring designed for short wheelbase Land Rover Series vehicles. This road spring is configured with 11 leaves and is intended ...

Carburettor Spring - Solex - a spring used in the Solex carburettor of the 2.25 litre petrol engine, part of the fuel system. It supplies the spri...

Door Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Exhaust Pipe - Intermediate - Non-Station Wagon

Shackle plate

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...