Land Rover Parts

Right-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the right cylinder bank exhaust manifold outle...

Road Spring - rear coil spring for vehicles equipped with self-levelling suspension. The spring locates in the rear suspension and works in conjun...

Front Door Sliding Glass - sliding glass pane for the front door window. Runs within the door-top window channels, forming one of the sliding pane...

Olive compression ferrule for a pipe union. The olive seats between the pipe and the union nut, forming a compression seal at the joint as the nut...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Interior Lamp Lens for the interior courtesy lamp. The translucent lens clips over the lamp body, protecting the bulb and diffusing its light into...

Exhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...

Oil Filter for the 2.7L TDV6 diesel engine, part of the engine lubrication circuit. A paper-element filter that removes wear particles and contami...

Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...

Bulb rated at 24V 5W, for use in side lamp and parking light circuits on 24V vehicle electrical systems. Small-wattage bulb designed for marker an...

Exhaust Valve for the 2.6L 6-cylinder IOE (inlet-over-exhaust) petrol engine, forming part of the cylinder head and block valvetrain. The exhaust ...

Steering Box Bearing - Manual is a needle bearing fitted inside the manual (non-power-assisted) Gemmer steering box. The bearing supports the sect...

Rear suspension panhard rod retaining bolt used in the Radius Arms & Links assembly. This bolt secures the panhard rod to its mounting bracke...

Starter Solenoid for the starter motor on 2.5 litre four-cylinder diesel engines. Mounted on the starter motor within the engine cranking circuit,...

Shock Absorbers for the rear axle, supplied as a matched pair. Each damper controls suspension movement by converting the energy of spring oscillat...

Fuel Tank Bolt - shouldered mounting bolt in the fuel tank support assembly, securing the tank mounting to the chassis outrigger. The plain should...

Windscreen Hinge - left-hand - for the Defender fold-flat windscreen assembly. This hinge forms one of two pivot points at the lower edge of the w...

Torx Countersunk Screw is a fixing used within the upper tailgate assembly. The countersunk head seats flush with the mounting surface, while the ...

Seat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...

Front Fuel Tank Outrigger is a chassis outrigger welded to the main frame rail, located at the rear of the front fuel tank to support and locate th...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. This pulley operates within the A/C belt drive circuit, maintaining ...

Experience the power and engineering of a classic V8 engine with the Haynes V8 Petrol Engine Model Kit. This fully functional, motorized model is d...

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...

Upper Tailgate Gas Support Strut for the Range Rover P38 rear body assembly. This gas strut supports the upper tailgate in the open position, hold...

Brake hose assy. fr. LH D3, D4

Front Radius Arm Nut - an M16 self-locking Nyloc nut used at the front radius arm mounting, part of the front suspension linkage. The radius arm l...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Clevis Pin for the clutch cross shaft, part of the mechanical clutch release linkage. The pin forms the pivoting joint that connects the clutch op...

Rope Hook

Driving Member Bolt secures the driving member, or drive flange, to the wheel hub. The driving member transmits drive from the axle halfshaft to t...

Wheel Brake Cylinder is the rear wheel cylinder of the drum brake assembly. It converts hydraulic pressure from the brake circuit into mechanical ...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Flasher Unit - the switching relay of the direction indicator and hazard warning circuit. It provides the timed make-and-break that pulses the ind...

Window Regulator for the left-hand front door, operating the manual window lift mechanism. The regulator converts the rotation of the winder handl...

Rear Light Guard - Single - Black is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from impa...

A/C fan assembly D2

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Shaft coupling

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Fits Land Rover Defender (1987-2016) Wolf style design for a tough, military-inspired look Sold as a pair for full headlamp protection

Jet windscreen wash RRclassic 1986 - 1991

Outer left front wing panel forming the exterior body section above the front wheel arch. Designed as a replacement outer wing panel for the left-h...