Land Rover Parts

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Injection Pump Gasket for the fuel injection pump assembly on the 2.5L 4-cylinder naturally aspirated and turbocharged diesel engines. Seals the m...

High-Tensile Bolt - 1/2" UNF x 3" for use in Land Rover chassis, body, and mechanical assemblies where a 1/2" UNF thread and 3" length is specified...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Wheel Nut for Steel Road Wheels - M14 × 1.5 thread. Secures steel road wheels to the wheel hub studs. Sold individually; five nuts are required pe...

Engine Plug - a threaded blanking plug used to seal machined ports and drillings in the engine, including locations in the cylinder head and the oi...

Worklamp Autolite square 1x 55W

Steering Box - LHD is the manual steering gearbox at the heart of the steering system. It converts rotation of the steering wheel and column into ...

Side Steps - a matched left- and right-hand pair of tubular side runners that bolt to the sill and chassis mounting points, forming a continuous no...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Oil Pump Assembly for the engine lubrication system of the 4-cylinder non-TDi engine range. Driven from the engine, the pump draws oil from the su...

These locking wheel nuts are suitable for all alloy wheels that use original Land Rover alloy wheel nuts. Set of 5 locking wheel nuts and 1 key.

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Bump Stop - rear suspension bump stop that limits the upward travel of the axle at full compression. The moulded rubber block cushions the contact ...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Wheel Stud - Front Drive Shaft Hub is a press-fit threaded stud for the front drive shaft hub assembly. It provides the fastening point that secure...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Joint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...

Kit - 7 Inch Headlamp Fixing - Series - Defender

Headlamp Mounting Gasket for the headlamp assembly. A rubber gasket that seats between the headlamp unit and the body aperture surround. It provid...

Flasher Relay for the Discovery 1, controlling the flash rate of the turn signal (indicator) circuit. This electronic relay unit regulates the fre...

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Steel Jerry Can with a 20-litre capacity. A pressed and welded steel liquid carrier built to the traditional jerry can pattern, used to carry a res...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Power steering seal kit

Fuel Gauge is a 12V dash-mounted instrument that displays the amount of fuel remaining in the tank. Fitted within the instrument panel, it receive...

Fuel Pump is a low-pressure in-tank unit forming part of the fuel delivery system on petrol applications. Mounted inside the fuel tank, it acts as...

Air flow meter OEM VDO

Intercooler is the charge-air heat exchanger of the turbocharger induction system. It sits between the turbocharger outlet and the engine intake, ...

Radiator Hose - a moulded coolant hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries engine coolant between th...

Radiator Hose for the Range Rover P38 cooling system, fitted to V8 Petrol engine variants. This hose forms part of the engine cooling circuit, con...

Drop arm LHD RRcl, D1 92>

Bottom Radiator Hose - the lower coolant hose in the engine cooling circuit, connecting the radiator outlet to the water pump inlet. It returns co...

Handbrake Cable transmits lever movement to the transmission handbrake, the drum brake mounted on the transfer box rear output. The outer sheath i...

Bump Stop limits suspension travel within the suspension assembly, cushioning the contact between the axle and chassis at the extremes of wheel mov...

Radius Arm Bush Set - Polyurethane fits at the axle end of the front radius arms, within the front suspension radius arm and axle location assembly...

Coolant hose RRcl 3.5

Rear Exhaust Silencer for the Land Rover Defender 90 fitted with the V8 petrol engine. This silencer box forms part of the rear exhaust assembly, ...

Exhaust Downpipe for the Land Rover Defender fitted with the 4-cylinder 2.5-litre naturally-aspirated diesel engine. This primary exhaust pipe con...

Plate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...

Packing Strip fitted between the bulkhead base and the footrest bracket mounting on the chassis of Defender 90/110. This strip provides the correc...

Coolant Hose carries coolant between the radiator and the engine within the cooling circuit. Moulded for the 2.25L carburettor petrol engine fitte...

Radiator Hose for the engine cooling system, specific to the 2.25L Petrol engine with standard duty radiator. This hose connects the engine to the...

Track Rod Tube for the front steering linkage of the Discovery 1 and Range Rover Classic. The track rod tube forms the central threaded section of...

Windscreen Seal is a rubber glazing seal fitted around the windscreen aperture. It retains the windscreen glass in the body aperture and seals the...

Rear Door Lock Cover Gasket, the seal fitted behind the rear door handle and lock cover. It seats between the exterior handle/lock cover and the o...