Products

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Spring plate

Locking plate

Steering Box Side Plate Gasket seals the side cover plate against the casing of the manual steering box. It sits between the dowel-located side pl...

This brake drum is designed for long wheelbase Land Rover Series II and Series IIA vehicles. It is a drum brake component intended for use in tradi...

Road Spring SWB Rear 11L

Front Exhaust Pipe for petrol applications. This is the front section of the exhaust system, carrying gases from the exhaust manifold rearward to t...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Brake master cyl SII SWB

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Washer used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...

Crankshaft Oil Seal is the outer (rear) crankshaft seal in the engine sealing arrangement, fitted where the crankshaft exits the cylinder block. S...

Grab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...

Cup Plug - a cup-type core plug (also known as an expansion or welch plug) that seals a casting core hole in the cylinder block or cylinder head. ...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Bolt with a 5/16" UNF thread and a shank length of 2-3/4 inches. A standard-thread fastener used in assembly of the four-cylinder engine. Applies ...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Crankshaft - 3-Bearing

Gudgeon Pin Bush - the small-end bush pressed into the connecting rod for the gudgeon pin. It forms the bearing surface between the gudgeon (pisto...

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Sump - 2.25 Petrol/Diesel - 2.5 Petrol is the engine oil sump (oil pan) for the 2.25L 4-cylinder petrol, 2.25L 4-cylinder diesel, and 2.5L 4-cylind...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Shim .003" for swivel pins

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Steering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...

Stud for the front axle swivel pin housing - a threaded stud that provides a fixed anchor for fastening a mating component to the swivel pin housin...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Brake shoe spring 109 rear lower

Alternator Belt for the 2.5L four-cylinder petrol engine. This drive belt runs from the crankshaft pulley to the alternator, turning the alternator...

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...