Products

Coupling Assembly - union fitting for the engine oil cooler pipe circuit. This union connects adjacent oil cooler pipe sections in the engine bay,...

Dump Valve

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Axle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...

Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...

Spring Seat for the front coil spring suspension. It forms the lower seat that locates and supports the base of the front coil spring on the axle, ...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Flexible Rubber Mounting Bush for the Land Rover Discovery 1 and Range Rover Classic. This rubber isolator bush is used in various under-bonnet mo...

Fuel Filter Housing Assembly for the fuel delivery line on carburettor petrol engines, including the 3.5L V8. This assembly mounts in-line between...

Crankshaft Position Sensor for 4-cylinder petrol applications - 1.8L K Series and 2.0L MPi T Series - mounted at the crankshaft in the engine block...

Crankshaft Position Sensor for 4-cylinder petrol applications - 1.8L K Series and 2.0L MPi T Series - mounted at the crankshaft in the engine block...

Camshaft Position Sensor for the EFi V8 petrol engine, part of the ignition and engine management sensor group. The sensor supplies the camshaft r...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Locknut is a self-locking M10 nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibration, m...

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Hexagonal Thin Nut, 7/16" UNF, used within the clutch hydraulic circuit at the master cylinder and pipe connections. The reduced-height (thin) pro...

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Centre Exhaust Silencer located in the mid-section of the V8 exhaust system, between the front downpipe assembly and the rear silencer. Designed f...

Cleaner Air Filter Element

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Rear lower link bush set in polyurethane, part of the rear suspension link assembly. The rear lower links (bottom links) locate the rear axle long...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

A-frame bush for the rear suspension upper link, part of the rear axle location assembly. The A-frame is the upper link between the rear axle and ...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Polyurethane Bush for the rear suspension upper link, part of the rear A-frame top link and fulcrum arrangement. The bush locates the upper link a...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...