Products

Gasket - Cylinder. Head Front Cover

Gasket round shape type, cover

Gasket - Cylinder. Head Front Cover

Gasket Kit

Front spring pad for the front suspension strut and coil spring assembly. The pad is an elastomer insulator that seats between the end of the coil...

Fuel Pump O-Ring Seal, 31mm x 2mm - the sealing ring at the fuel pump / fuel injection pump joint. This O-ring is the only seal at that joint, so ...

Fuel Pump O-Ring Seal, 31mm x 2mm - the sealing ring at the fuel pump / fuel injection pump joint. This O-ring is the only seal at that joint, so ...

Water Pump for the engine cooling circuit. The pump circulates coolant through the cylinder block, cylinder head and radiator to maintain engine op...

Water Pump for the engine cooling circuit. The pump circulates coolant through the cylinder block, cylinder head and radiator to maintain engine op...

Water Pump for the engine cooling circuit. The pump circulates coolant through the cylinder block, cylinder head and radiator to maintain engine op...

Clutch slave cylinder assembly

Remote Control Receiver is part of the vehicle anti-theft alarm system, operating on the 433MHz radio frequency band. It receives the coded radio ...

Throttle body with integrated actuator motor for the 2.2L DW12 common-rail diesel engine. Mounted in the intake tract ahead of the inlet manifold,...

Throttle Body and Motor - the electronically actuated intake throttle valve for the 2.2L common-rail direct-injection diesel engine, mounted at the...

Keyless Entry and Start Aerial is the receiver antenna for the passive keyless entry and push-button start system, part of the vehicle's anti-theft...

Gasket cylinder head Grade 3, 3 Hole, 1.22 MM Multi layered steel Reinz

Head Gasket - 3.0 TDV6 - Grade 3

Head Gasket - 3.0 TDV6 - Grade 3

Interior Trim Retainer Clip - a moulded fastener used to secure interior trim to the vehicle body. The clip retains door casings, pillar trims and...

Trim clip used to retain trim panels to the body structure. Size 8.5 mm, with a panel grip range of 0.8 to 2.2 mm. The clip locates through the pa...

Windscreen Washer Pump - the combined motor and pump unit mounted in the washer reservoir, part of the Windscreen Wash and Wipe system. When the w...

Fuel Filler Restrictor for diesel vehicles, fitted inside the fuel filler neck as part of the fuel tank and filler assembly. It forms a physical b...

Starter Motor for the 2.2L Td4 diesel engine (DW12), part of the engine starting system. It cranks the engine through a pinion that engages the ri...

Exterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...

Exhaust Gas Temperature Sensor for the front position in the exhaust front pipe and catalyst assembly. The sensor threads into the front pipe upst...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Brake Caliper Bleed Screw for the front and rear brake calipers. The bleed screw threads into the bleed port on the caliper body and is opened to ...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Air conditioning expansion valve - the refrigerant metering device mounted at the evaporator inlet on the heating and air conditioning housing. It...

Turbocharger Oil Feed Filter for the 2.2L four-cylinder common-rail diesel engine. It sits in the turbocharger oil supply line, between the engine ...

Camshaft Position Sensor mounted in the cylinder head cover of the 2.2L four-cylinder common-rail diesel engine, reading the target on the camshaft...

Camshaft Position Sensor mounted in the cylinder head cover of the 2.2L four-cylinder common-rail diesel engine, reading the target on the camshaft...

Exhaust Manifold Nut is a hexagon nut used on the exhaust manifold fixings of the 2.2L 16V common-rail diesel engine (DW12). Manifold fasteners ru...

Cylinder Head Gasket seals the joint between the cylinder head and the cylinder block on the 2.2L 16V common-rail diesel engine (DW12), containing ...

Cylinder Head Gasket seals the joint between the cylinder head and the cylinder block on the 2.2L 16V common-rail diesel engine (DW12), containing ...

Cylinder Head Gasket seals the joint between the cylinder head and the cylinder block on the 2.2L 16V common-rail diesel engine (DW12), containing ...

EGR Vacuum Control Valve for the exhaust gas recirculation system on 2.2L diesel engines. The valve sits in the vacuum circuit between the vacuum ...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Flywheel Bolt for the 2.2L DW12 common-rail turbo diesel engine, securing the flywheel to the rear flange of the crankshaft. Hexagonal head, M8 x ...

Flywheel Bolt for the 2.2L DW12 common-rail turbo diesel engine, securing the flywheel to the rear flange of the crankshaft. Hexagonal head, M8 x ...

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...