Products

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

parts catalogue SII & SIIa orginal (1968)

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Cap adjusting

Rear Axle Case Bolt for the Salisbury rear axle. The bolt clamps the axle casing joint of the Salisbury (heavy-duty) rear axle, keeping the housin...

Axle Shim for the Salisbury rear differential, 0.003" thickness. This imperial-dimension shim is used during differential overhaul to set pinion s...

Salisbury Axle Shim used in the differential assembly of the Salisbury rear axle. This shim is positioned against the inner pinion shaft bearing a...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Differential Crown Wheel and Pinion Set for the LT95 four-speed gearbox used on V8 applications. The set provides the matched crown wheel and pini...

Starter Bush Kit - the set of bronze bushes that support the armature shaft of the inertia-type starter motor (Lucas Type 2M100) used on 4-cylinder...

Fuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Fuel Tank Sender for the rear-mounted fuel tank on long-wheelbase diesel applications. The sender unit fits into the top of the fuel tank, where a...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Exhaust Plate for the intermediate section of the exhaust system on 88" Short Wheelbase variants in left-hand drive (LHD) configuration. This plat...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Pan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Windscreen Seal - 2.5m is the rubber glazing seal for the windscreen, supplied as a 2.5 m length. It seats the windscreen glass in its aperture an...

Screw securing the front catch of the rear side sliding window. Used to fix the sliding window catch on Station Wagon bodies of early Series models.

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Screw for securing the chaffguard to the body structure on Series Land Rovers. The chaffguard protects adjacent components from abrasion and heat;...

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Inlet manifold stud

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Halfshaft Collar is a locating collar fitted to the front axle halfshaft. It seats against the inner side of the halfshaft bearing (244150), setti...

Gearbox Thrust Washer