Products

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Speedo cable oil seal retainer plate

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Ball Steel Bearing

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

LED Festoon Bulb for interior lamps. A double-ended festoon LED that replaces the standard filament festoon bulb in the courtesy, map and interior...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Rocker Shaft Spring for the Rover V8 valvetrain, fitted on the rocker shaft assembly. The spring acts as a spacer between adjacent rocker arms, ho...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Bolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Autogear Power Syn 75W90 5L

Gearbox Oil 75W80 is a 75W80-grade manual transmission fluid (MTF) formulated for the R380 5-speed manual gearbox. It lubricates the gears, synchr...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Clutch Plate

Clutch Plate

Clutch Driven Plate - the friction disc of the clutch, splined to the gearbox input shaft and clamped between the flywheel and the clutch cover. I...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Screw is a threaded fastener used to secure components during assembly.

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.