Products

24v dsl long belt

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

GENUINE LR camshaft sprocket for Rover V8 engines

Heater Control Bulb illuminates the heater and ventilation control panel. Fitted into the front HVAC control assembly, it backlights the heater co...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Front Fog Lamp is the right-hand front fog lamp assembly within the exterior front lighting system. Mounted in the right-hand side of the front bu...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Clip used to secure and locate a pipe or hose along its routing, retaining the line in position to prevent movement and chafing against adjacent co...

Air Suspension Connector is a push-fit (Voss-type) pneumatic connector used in the air supply and control circuit of the electronic air suspension ...

Active Cornering Enhancement (ACE) Pump for the Discovery 2. This hydraulic pump is the primary pressure source within the ACE system, which activ...

Bracket - Mtg

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Power Steering Hose forms the low-pressure feed line of the power steering hydraulic circuit, carrying fluid from the reservoir to the inlet of the...

Spare Wheel Carrier is the mounting bracket assembly that carries the spare wheel on the rear door. It bolts to the rear door and provides the stu...

Door Glass Channel for the side door glass assembly. The channel locates within the door frame and guides the window glass along its travel as it i...

Interior Mirror & 2 - Discovery 1

Seat Back Foam Pad is the foam cushion for the front seat backrest. Fitted over the seat frame and beneath the seat cover, it provides the backres...

Gaiter Bezel - Gear Lever - the trim surround that frames the gear lever gaiter where it meets the centre console, forming part of the console trim...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Roof Drip Rail Finisher is an exterior moulding that caps the roof drip rail. It runs along the roof-to-body joint, covering the drip channel to g...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Screw is a fixing screw used to secure exterior lamp, interior lamp and trim components to the body. It retains fittings such as the high-level st...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Grille Grommet - a mounting grommet for the front grille and headlamp surround panel. It seats in the body panel to receive and retain the grille ...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.