Products

24v dsl long belt

Turbocharger for the 2.0L AJ200 / AJ20D4 four-cylinder diesel engine. It sits in the forced-induction circuit between the exhaust manifold and the...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Valve Stem Seal for the cylinder head valvetrain on TDV6 and TDV8 diesel engines. Fitted to both inlet and exhaust valves, the seal presses onto th...

Kit - Drive Belt

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Clamp - Tube

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Timing Chain & Tensioner Kit - Upper

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Camshaft Pulley Hub mounts to the front of the right-hand (RH) cylinder bank camshaft on the 2.7L and 3.0L V6 diesel engine, forming part of the ti...

Oil Tube Gasket seals the turbocharger oil drain (return) pipe where it joins the engine, within the turbocharger lubrication circuit. After lubri...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Thermostat O-Ring for the TDV6 diesel engine. This O-ring provides the coolant seal at the thermostat housing on TDV6 diesel engines, preventing c...

Oil Separator Seal - sealing gasket for the oil separator in the crankcase ventilation system of the 2.7 and 3.0 litre V6 diesel engines. The oil ...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Banjo Washer for the oil feed pipe banjo union at the turbocharger, used on TDV6 2.7L/3.0L and TDV8 3.6L/4.4L diesel engines. This sealing washer ...

Gasket - Oil Tube

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

O-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...

Screw and Washer - Hex Head

Bolt

Air Cleaner Housing Insulator locates and cushions the air cleaner (air box) assembly on its mounting. The rubber insulator secures the air cleane...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

Oil Sump Gasket seals the oil pan (sump) to the cylinder block on the V6 diesel engine. It maintains an oil-tight joint at the base of the engine,...

Trim Clip that secures interior and exterior trim panels, door finishers and mouldings to the body. The clip locates in a pre-formed panel apertur...