Products

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Roller Bearing for use in drivetrain and mechanical assemblies.

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Sealing Washer for the coolant temperature transmitter adaptor, for use on the 2.25L Diesel, 2.5L Diesel, and 2.5L Turbo Diesel engines. Fitted at...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Starter Solenoid Relay for 12V petrol engines, acting as a high-current switching relay in the starting circuit. When energised by the ignition sw...

Brake Vacuum Tank for the Land Rover Series III 2.25 Diesel. Fitted in the brake servo vacuum circuit, the tank stores a vacuum reserve to ensure c...

Instrument Voltage Stabiliser - a thermal bimetallic unit mounted on the back of the instrument cluster that regulates the supply voltage to the fu...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Alternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Dowel A locating dowel for the engine cylinder block and cylinder head assembly. It seats in machined bores to align the cylinder head to the bloc...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Axle casing oil seal

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Stud for use in Land Rover gearbox assembly.

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

Transfer Case Intermediate Gear with a 44/22 tooth configuration, operating within the transfer box gear train. The intermediate gear meshes with ...

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

Oil Seal - Clutch Withdrawal Sleeve for the Land Rover Series 2A gearbox, specifically the partially synchronised variant fitted with a sealed clut...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Washer for the under-seat fuel tank front mounting assembly. This special-profile washer provides a secure bearing face at the front attachment po...

Four-Wheel Drive Selector Lever Bush for the transfer box gearchange linkage. The bush locates the four-wheel-drive selector lever at its pivot, t...

Core Plug - 1-3/8 in. diameter, threaded - for the Series engine block. This threaded plug seals a casting aperture in the engine block, retaining...

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Return Spring for Series hydraulic actuator and throttle control assemblies. This spring serves as a return spring in the hydraulic actuator assem...

Brake Lining Set for the rear drum brake assembly. This set contains the friction linings for both rear brake shoes, forming the braking surface b...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Copper Sealing Washer - a general-purpose copper crush washer used to seal threaded joints, plugs and unions. The soft copper deforms as the fitti...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...