Products

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Nut FQA

Nut Plate - captive fixing plate used at the rear body upper mountings. The plate holds the nut captive behind a blind or closed panel section, so...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

LED Direction Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It uses an L...

NAS Indicator Light - LED Clear 95mm - a single 95mm LED indicator lamp with a clear lens, designed to NAS (North American Specification) lamp dime...

LED Direction Indicator Lamp - Smoked is a rear direction indicator lamp to NAS (North American Specification) pattern in the 95mm round format, fi...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Steel Road Wheel, 5.5J x 16, of welded construction for tube-type tyre fitment. The rim is designed to run with an inner tube rather than a tubele...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Fuel Pump Joint Washer Sealing washer for the mechanical fuel pump mounting on the 2.6 litre 6-cylinder petrol engine. The washer fits between the...

Electric Fuel Pump - an SU-type electric fuel pump in the low-pressure fuel delivery circuit. It draws petrol from the tank and delivers it to the...

Idle Adjusting Needle is the mixture-adjusting needle for the Zenith Stromberg CD175 constant-depression carburettor fitted to the Rover 3.5 V8. I...

Plain Washer M8

Fitting Kit for Pacet Fan

Thermostat Kit for Electric Fan Kenlowe

Rear Wing Protector - a protective panel fitted over the rear wing to shield the bodywork from scratches, denting and wear during loading and off-r...

Sliding Window Seal Kit - Rear

Seat belt SECURICON

Glass Retainer Kit for the rear safari door window - the aluminium retaining strips that hold the fixed glass in the door frame. The strips clamp ...

Color of the pin may differ.

Shock absorber front Disco II OME BA 2228

Rear Rubber Mat for the rear floor and load area, cut to suit short-wheelbase County-specification vehicles. The moulded rubber mat protects the r...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Waterproofing Kit - V8 seals the ignition system of the V8 petrol engine against water and damp. The kit waterproofs the distributor and ignition ...

Towing Bracket Assembly Front-mounted detachable towing bracket that bolts to the front chassis to provide a towing and recovery point at the front...

Bumper End Plate Protector Pair - protection plates that fit over the outer ends of the front bumper. Supplied as a left- and right-hand pair, the...

Bulb is a 12V 21W single-filament bulb with a red finish, fitted in rear lamp assemblies. The single filament provides a single-intensity function...

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Haynes Military Land Rover Enthusiasts' Manual

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Bolt 1/4" UNF x 2-1/2"

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Bolt

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 4" shank length. A long-shank hex-head fastener for general assembly and fixin...