Products

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt Fixing bolt, 3/8" UNF x 2-1/2", used to secure the rear fuel tank to the chassis.

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 4-1/2" shank length. A long-shank hex-head fastener for general assembly and fi...

Bolt - 1/2" UNF x 2-1/2" is a UNF hexagon head bolt used in hardware and fixings applications on Land Rover vehicles. Thread specification 1/2" UN...

Bolt - 1/2 UNF x 4.5. Hexagon-head threaded fastener, 1/2 inch UNF thread by 4.5 inch length, used on military-specification chassis and body appl...

Bolt - 1/2" UNF x 5" used as the centre shackle pin bolt in the leaf spring suspension assembly on 109" 1-Ton models. This bolt secures the centre...

Steel ball 1/4"

Chassis Wiring Harness for the short-wheelbase chassis, incorporating the wiring for the fog and reverse lamps. It runs the length of the chassis a...

Distance Piece for the LT76 gearbox mainshaft. This spacer maintains the correct axial position of components along the mainshaft within the LT76 ...

Thermostat Housing Gasket seals the joint between the thermostat housing and the cylinder head water outlet in the engine cooling circuit. It main...

Inner Pinion Bearing for the Salisbury rear axle. This taper-roller bearing supports the inner end of the differential pinion shaft, carrying the ...

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...

Steering Relay Mounting Bolt - secures the steering relay to the chassis within the steering linkage. The steering relay transfers movement into t...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Glass seal EPDM

Jubilee Clip - 60-80mm is a worm-drive hose clip with a 60-80mm clamping range. The band is tightened by a captive worm screw to secure large-bore...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Radiator panel Series 2/2A - suffix B to suffix F

HUB & BEARING KIT - S2A FROM SUFFIX H - S3 UP TO 1980

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Tailgate Seal Kit for the rear tailboard and tailgate. Reseals the rear tailboard and tailgate opening. The kit contains two tailboard seals, one ...

Fuel Tank Outrigger is a rear chassis outrigger forming part of the body & chassis assembly. It welds to the main chassis rail to support the ...

Front Fuel Tank Outrigger is a chassis outrigger welded to the main frame rail, located at the rear of the front fuel tank to support and locate th...

Fuel Tank Outrigger - front right-hand chassis outrigger supporting the fuel tank on the short-wheelbase 88" chassis. Welded to the chassis frame,...

Safari Rear Door Skin - Lower Half. The outer sheet-metal panel for the bottom half of the rear side door (the Safari door), supplied as a repair s...

Cubby Box - a centre console storage box that mounts on the transmission tunnel between the front seats. The body is finished in grey with a vinyl...

Rear Door Trim Panel - a black interior trim panel that finishes the inner face of the rear side-hinged door, covering the door frame to give a cle...

Weber Carburettor Conversion for the 2.25L petrol engine, replacing the original Solex carburettor. This progressive downdraught Weber unit instal...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Front Wing Panel is the outer body panel that forms the side of the front end over the front wheel arch, part of the front body assembly. Supplied...

Sill Protector - chequer plate panel set for the outer sill panels, part of the exterior body protection group. The plates mount along the outer s...

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

Rear 3-Man Bench Seat Techno Wide 1.21 m

Rear Door Goal Post Cladding - Safari is a three-piece exterior trim set for the rear door goal-post surround. It clads the upper goal-post and pi...

Restore the performance of your Land Rover Series with this AVM Freewheeling Hub Repair Overhaul Kit. Designed for 10-spline freewheeling hubs, thi...

Free-Wheeling Hub Repair Kit for 24-spline manual free-wheeling hubs. Manual free-wheeling hubs allow the front drive members to be disengaged fro...

Rear Quarter Chassis Section for the short-wheelbase (88") chassis, supplied with the rear leaf spring hangers. This pressed and welded steel sect...