Products

High Range Gear is the intermediate high-range gear in the integral transfer section of the LT95 gearbox. With 40 teeth and a 1.34:1 ratio, it set...

Sealing Plug for the transmission handbrake drum on the LT95 four-speed gearbox. The drum-type transmission handbrake acts on the transfer box out...

Fitment: All models to (VIN) KA930455 All models 1980 on

Stub Axle - rear stub axle carrying the hub and bearings at the rear axle. Bolted to the rear axle casing, it forms the fixed spindle on which the...

1st Speed Gear - first-gear wheel for the LT76 four-speed gearbox. It forms part of the gearbox gear train, meshing with the layshaft to provide t...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

O-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Synchromesh Assembly First/second gear synchromesh assembly for the LT95 four-speed gearbox. Synchronises shaft and gear speeds during 1st-to-2nd ...

Transfer Case Bottom Cover Gasket for the LT95 combined gearbox and transfer case. It seals the joint between the bottom cover and the transfer ca...

Transfer Box Bottom Cover Cover plate that closes the underside of the transfer box casing. Seals the bottom of the transfer box housing, retainin...

Wheel Stud for use with Wolf-style rims in the wheel hub assembly. This 60mm long, 15mm diameter stud locates the wheel to the hub and secures it ...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Rear Propeller Shaft for the rear driveline. The propeller shaft transmits drive from the transfer box rear output flange to the rear axle differe...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Differential Repair Pan is the pressed cover that closes the underside of the axle differential housing, retaining the oil and protecting the crown...

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Rear End Door Hinge Kit replaces the full set of hinges that carry the rear end door on the body. The kit contains three hinges in a zinc-plated f...

Exhaust Fitting Kit supplies the seals and fixings needed to install and join a complete exhaust system on the short-wheelbase (SWB) chassis. The ...

Front Door Seal Kit re-seals the right-hand front door aperture, supplied with the rivets needed to fit it. The kit contains six door sealing rubb...

Front Door Seal Kit for the left-hand front door, supplied with the rivets required for fitting. The kit contains the door sealing rubbers to re-s...

Rear Safari Door Seal Kit for the Safari-style rear door assembly on Series 2, 2A, and Series 3 Land Rovers. This kit contains all the rubber seal...

Fuel Tank Outrigger - front left-hand chassis outrigger supporting the fuel tank on the short-wheelbase 88" chassis. Welded to the chassis frame, ...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Tailboard Hinge Bracket Kit provides the bolt-on hinge assembly for a drop-down rear tailboard, mounting the tailboard to the rear body so that it ...

Headlamp Mounting Kit (Black Bezel) - a single mounting assembly for a 7-inch round headlamp unit, forming part of the front lighting installation....

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

The Jackall 48" Large Base Jack is the ultimate heavy-duty lifting solution for a variety of applications. With a massive 8,000lbs capacity, this j...

Range Rover The First Fifty Product Description: Prototypes, YVBs and NXCs - the story of the early Range Rovers Today, the Range Rover is a lege...

Door pillar bracket for the left-hand side — the lower bracket that secures the foot of the front door pillar (A-post) to the bulkhead outrigger. ...

Kit contains: 2X MRC6982 2X MRC6980 2X MRC6985

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Coating Spray Gun, bottle-mount type, for applying protective coating. This Schutz-style gun screws directly onto the 750ml coating bottle, so no s...

A/C fan assembly D2

Headlamp Bowl Kit for the 7-inch headlamp assembly on Series III and Defender vehicles. This kit comprises the plastic headlamp backing bowl and t...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...