Products

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Flasher Relay installed in the indicator and hazard-warning circuit, controlling the flash rate of the turn-signal lamps. This 12V electronic unit...

Emergency Bulb and Fuse Kit - 12 volt, for vehicles using H4 headlamp bulbs. A compact set of replacement bulbs and fuses to carry in the vehicle,...

Coloured Lamp Kit is a complete set of 73mm round lamps for the front and rear lighting positions, supplied with coloured lenses. The kit contains...

LED rear light upgrade kit, 95mm - replaces the round 95mm rear lamp units in the rear lighting circuit with sealed LED equivalents. The lamps are...

Upgrade your Land Rover Defender (1987-2006, 2007-2016) or Series 3 with the WIPAC LED 73mm smoked lamp kit. Smoked LED style light for a sleek...

LED Light Kit - a Wipac clear-lens LED lamp set that replaces the standard 73 mm exterior lamps with LED units. The kit contains eight lamps plus ...

LED Light Upgrade Kit (coloured lens type) - a complete set of WIPAC 73mm LED lamps replacing the original incandescent front and rear exterior lam...

LED Light Kit upgrades the exterior lighting to a coloured-lens LED set. It comprises two front sidelights, two front and two rear indicators and t...

LED Light Upgrade Kit (deluxe smoked-lens type, 73mm) - a complete set of WIPAC LED lamps with smoked lenses, replacing the original incandescent f...

Parabolic Leaf Spring for the rear axle, supplied as a matched pair. A parabolic spring uses fewer, tapered leaves than a conventional multi-leaf ...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Static Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...

Seat Belt - 3-Point Inertia Reel is a lap-and-diagonal front seat belt assembly with a self-locking inertia reel, supplied to the basic Type A spec...

Gasket Set

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Transfer Box Gear Set - High Ratio is a gear set for the two-speed transfer box that raises the high-range gearing. By raising the high-range rati...

Brake Pipe Union for the hydraulic brake system, a male fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic circ...

Blind Brake Union - a male threaded fitting used in the hydraulic brake pipe circuit. The body carries a 3/8"-24 UNF male thread but is solid, wit...

Brake Union for the hydraulic braking circuit, with male 7/16"-20 UNF thread for 1/4" diameter brake pipe. This male-threaded end fitting connects...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Brake Union – a threaded fitting in the hydraulic brake circuit that joins and seals brake pipe. Female union with a 7/16"-20 UNF thread, sized fo...

Rubber isolator clamp used in the bonnet-mounted jack bracket assembly to secure the jack beam or handle against the bonnet mounting brackets. The...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Spare Wheel Carrier Spacer for the rear-door mounted spare wheel carrier. It spaces the spare wheel carrier stud mounting on the rear door, settin...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Wheel Wrench a 27mm wheel brace for loosening and tightening wheel nuts. The 27mm socket end matches the wheel nuts fitted to the applicable vehic...

Body is the right-hand sill channel for the Defender, running along the underside of the door aperture in the body structure. This structural chan...

Body

Ball joint RH OEM LEMFORDER

Joint - Ball

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Indicator front/rear LED clear lens

This unit provides position illumination at the front of the vehicle and interfaces with the vehicle's electrical lighting circuit and mounting ape...

Front Clear Side Light LED 12V

Front Side Lamp with a clear lens and LED illumination, mounting in the front lighting position to serve as the side (parking) light. The LED draw...

Designed for Defender 2007-2016 Smoked lens for a stylish, modern look High-quality 73mm LED light for superior brightness and efficiency Mu...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Rear Stop/Tail Lamp - LED - LED combined stop and tail lamp with a red lens, supplied as a complete sealed unit to replace the standard rear stop/t...

Rear Stop/Tail Lamp - LED, Smoked - LED combined stop and tail lamp with a smoked lens, supplied as a complete sealed unit to replace the standard ...